Drive safeEmissions-only fault. Safe to drive - fix at your convenience (often just the gas cap).
Your gas cap is loose or missing - that's the most common cause by far. Tighten it until it clicks and the light may go off on its own after a few drives.
Model notes: This is the 'you left the cap loose' code - it is designed to be the easy one. Always start with the cap and give the self-test time to run before further diagnosis.
Key facts
P0457 means evaporative emission control system leak detected (fuel cap loose/off). Your gas cap is loose or missing - that's the most common cause by far. Tighten it until it clicks and the light may go off on its own after a few drives. WrenchFair's published fair-price range for this repair is $15–$80 parts and $0–$180 labor at independent shops.
WrenchFair rates P0457 a 1-of-5 DIY difficulty (“Tighten or replace the gas cap first - this code exists specifically for that scenario.”) with a “Drive safe” driveability rating: Emissions-only fault. Safe to drive - fix at your convenience (often just the gas cap). These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 434 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
Emissions warranty: P0457 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2013–2019 Ford Escape (1.6L EcoBoost, 2.0L EcoBoost) — EVAP purge valve replacement:Owner-verified
The purge valve sits on the driver's side of the engine bay at the front of the engine — on the 1.6L owners reach it after removing the air cleaner assembly. It comes as a valve-plus-hose assembly (Ford CV6Z-9D289-T for the 1.6L, CV6Z-9D289-S for the 2.0L — confirm by VIN, as build time matters). Disconnect the electrical connector, pop the quick-connect vapor lines off, and swap the assembly. One owner caution: don't replace just the solenoid body if the hoses are the updated part — match the whole assembly.
Do this test first: Tighten the gas cap until it clicks several times, or replace it if the seal is damaged or the cap is missing
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0457 on the 2013–2019 Ford Escape — but the community-sourced EVAP purge valve replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Purge valve mounting: verify — Plastic quick-connect assembly — no torque fasteners. Confirm part number against VIN before ordering.
Tips
Classic symptom: hard starting or stalling right after filling the tank — a purge valve stuck open floods the engine with raw fuel vapor.
Test the old valve before replacing: remove it and blow through it — you should NOT be able to blow through a good closed valve.
Stop topping off the tank after the pump clicks — repeatedly cramming extra fuel in soaks the charcoal canister and kills purge valves early; owners flag this as the #1 repeat cause.
If P1450/P144C persists after a valve swap, suspect a fuel-soaked charcoal canister or the fuel tank pressure sensor — a smoke test finds the remaining leak.
Clear the codes after the repair and drive normally; EVAP monitors take several drive cycles to self-check, so the light won't clear instantly.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
fuel smell
failed emissions test
no drivability symptoms
slightly worse fuel mileage
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Loose, missing, or damaged gas cap (most common by far)
Cracked filler neck
Large disconnected EVAP hose
Stuck-open vent valve 3 owner notes link this repair to P0457
Owner notes linked to P0457: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Tighten the gas cap until it clicks several times, or replace it if the seal is damaged or the cap is missing Tests: Loose, missing, or damaged gas cap (most common by far)
Clear the code and drive normally - the EVAP self-test needs specific conditions and may take a few drive cycles
If the code returns with a good cap, smoke-test for a large leak elsewhere
Inspect the filler neck for cracks or rust holes Tests: Cracked filler neck
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2019 Ford Escape: EVAP purge valve replacement — test first, then buy for this job.
The price range below is a national planning range for P0457 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$15 – $80
Labor$0 – $180
Gas cap is under $25; smoke test plus hose/valve runs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0457 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
1 of 5 — Tighten or replace the gas cap first - this code exists specifically for that scenario.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →