p0442 on a 2012–2018 Ford Focus: Evaporative emission control system leak detected (small leak)
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
DIY difficulty 1/5
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0442 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Drive safeEmissions-only fault. Safe to drive - often just the gas cap.
Can I drive with P0442?
Can I drive with a P0442 code?
Yes. P0442 doesn't make your car unsafe to drive on its own. Emissions-only fault. Safe to drive - often just the gas cap. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.
How serious is P0442?
Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions-only fault. Safe to drive - often just the gas cap.
Will P0442 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Yes, if your state or county runs an OBD-II emissions test and the check-engine light is on. The test plugs into your car's computer, and under the EPA's OBD inspection criteria any code that commands the light on is itself a failure — no tailpipe reading needed.
Fixing the fault is only half the job. Clearing the code resets every readiness monitor, and they have to run again before the car will pass. The EVAP monitor is often the last to set — it only runs under specific conditions — so don't clear codes the week of your test. See the drive-cycle and readiness guide →
One break for EVAP codes: the EVAP monitor is the single monitor California excuses on 2000-and-newer gasoline vehicles, and in states following the EPA's allowance (up to two monitors not ready for 1996–2000, one for 2001 and newer) it can be your one allowed incomplete monitor. But that excuses an incomplete monitor, not a lit light — while this code is active and the light is on, the car still fails.
Not everywhere tests: some states have no emissions test at all (South Carolina is one), and in others only certain counties test — so there, this code alone won't block registration. Rules vary by county as well as state, and they change, so confirm with your state's DMV before test day.
Small leak in the system that captures fuel vapors. Nine times out of ten it's the gas cap - check that first.
VCDS tip: Clear the code after a gas-cap fix and complete two drive cycles before retesting.
Model notes: Tighten or replace the gas cap and drive two full drive cycles before doing anything else - this fixes it more often than not. Brand patterns: on Volvos the leak detection pump is a common culprit; on Chrysler/Jeep it is the ESIM module; on Hyundai and GM the purge valve.
Key facts
P0442 means evaporative emission control system leak detected (small leak). Small leak in the system that captures fuel vapors. Nine times out of ten it's the gas cap - check that first. WrenchFair's published fair-price range for this repair is $15–$500 parts and $0–$400 labor at independent shops.
WrenchFair rates P0442 a 1-of-5 DIY difficulty (“Gas cap first; smoke test if it persists.”) with a “Drive safe” driveability rating: Emissions-only fault. Safe to drive - often just the gas cap. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Emissions warranty: p0442 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2012–2018 Ford Focus (2.0L I4 (GDI Duratec Ti-VCT), 2.0L EcoBoost I4 (Focus ST)) — Canister purge valve sticks — P0456/P0442, collapsed fuel tank (18V735):Factory-documented
Driveway-able in under 30 minutes: one electrical connector and two vapor-line quick-connects on top of the engine.
Do this test first: Tighten/replace the gas cap and drive two cycles before anything else
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for p0442 on the 2012–2018 Ford Focus — but the community-sourced Canister purge valve sticks — P0456/P0442, collapsed fuel tank (18V735) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CPV mounting: verify — Slides onto a bracket — no torque fasteners; just seat the quick-connects until they click.
Tips
The canister purge valve sticks open or closed. Stuck open, it pulls excessive vacuum that can deform/collapse the plastic fuel tank, cause stalls, and make the fuel gauge lie — Ford recalled 2012-2018 2.0L cars for exactly this (18V735), then re-recalled cars repaired incorrectly (26V369 / Ford 26S40, owner letters July 2026).
Stuck closed or leaking, it sets P0456/P0442 and can cause hard starting or stumbling right after refueling.
Owner-verified DIY: the CPV is a ~$30-50 part on top of the engine — a 15-30 minute swap with basic hand tools, one of the highest-value DIY repairs on this car. Check your VIN for open recalls first; the dealer PCM reflash is free.
If the tank already deformed (gauge reads wrong, stall after fill-up), the recall covers tank, canister, and fuel-delivery-module replacement at the dealer — don't just swap the valve and ignore the tank.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Typical time: “Driveway-able in under 30 minutes: one electrical connector and two vapor-line quick-connects on top of the engine.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
fuel smell
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Loose or cracked gas cap (check first, always)
Cracked EVAP hoses
Leaking purge or vent valve
Rusty filler neck
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Tighten/replace the gas cap and drive two cycles before anything else
Smoke-test the EVAP system
Command the vent valve closed in output tests Tests: Leaking purge or vent valve
Most likely job on your 2012–2018 Ford Focus: Canister purge valve sticks — P0456/P0442, collapsed fuel tank (18V735) — test first, then buy for this job.
The price range below is a national planning range for p0442 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$15 – $500
Labor$0 – $400
A gas cap is under $25, but a real shop bill — a $60-$150 smoke test plus a purge/vent valve at $150-$400 installed, or a canister at $300-$700+ installed — typically lands $200-$400. The ranges above span all paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →