Diagnose soonDiesel emissions-system fault. Follow the diagnostic path; some affect drivability.
The heater plugs that help your diesel start on cold mornings have an electrical fault. Expect long cranking and clouds of white smoke on cold starts.
Model notes: Always replace glow plugs as a set and use a torque wrench - they snap off in the cylinder head if overtightened or forced, turning a simple job into a nightmare.
Key facts
P0380 means glow plug/heater circuit A malfunction. The heater plugs that help your diesel start on cold mornings have an electrical fault. Expect long cranking and clouds of white smoke on cold starts. WrenchFair's published fair-price range for this repair is $100–$500 parts and $200–$600 labor at independent shops.
WrenchFair rates P0380 a 3-of-5 DIY difficulty (“Glow plug replacement is straightforward on many diesels; some bury them under the valve cover.”) with a “Diagnose soon” driveability rating: Diesel emissions-system fault. Follow the diagnostic path; some affect drivability. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2001–2012 GMC Sierra HD (6.6L LB7 Duramax V8 diesel, 6.6L LLY Duramax V8 diesel, 6.6L LBZ Duramax V8 diesel, 6.6L LMM Duramax V8 diesel, 6.6L LML Duramax V8 diesel) — Glow plug control module failure (P0380) and individual glow plugs:Owner-verified
Controller and plugs are stocked at dealers and parts stores; module replacement needs only basic hand tools.
Do this test first: Measure each glow plug's resistance - they should all read similarly low; the outlier is dead
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0380 on the 2001–2012 GMC Sierra HD — but the community-sourced Glow plug control module failure (P0380) and individual glow plugs note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Glow plug installation: verify — Look up the factory torque before installing; over-torquing snaps plugs in the head.
Tips
Glow plug faults on LBZ-through-LML trucks (2006-2016) usually trace to one of four places: the glow plug control module, an individual glow plug, the wiring harness, or a combination. Common codes are P0380 (glow plug circuit A), P0382 (circuit B), and P0671-P0678 for individual cylinders.
The module sits at the top rear of the driver's side of the engine. The quick owner test: with the key on during the wait-to-start cycle, probe the glow plug rail with a test light. No power at the rail means the module is likely bad; power at the rail means chase individual plugs or wiring instead.
Do not ignore a glow plug fault just because the truck starts fine. A failed controller can over-cycle a glow plug or feed current to a dead one continuously, which swells the plug tip. A swollen tip is very hard to remove and risks dropping the tip into the cylinder.
On California-emissions trucks (YF5/NE1 codes in the glove box), a single failed glow plug will set P0380; federal-emissions trucks need several to fail before the code appears. Know which emissions package you have before diagnosing.
Replacement controllers are inexpensive and easy to swap (owners report under $150 and a short driveway job). Use ACDelco 9G glow plugs for LBZ, LMM, and LML trucks; they supersede the older 61G and are not compatible with 2004-2005 LLY engines.
Typical difficulty: Easy — based on 70 code guides for the glow repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
long cranking on cold starts
white smoke on startup
rough cold idle
glow plug light flashing
check engine light
glow plug light stays on longer than normal
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
One or more failed glow plugs (most common - they wear out like light bulbs)
Failed glow plug relay or control module 2 owner notes link this repair to P0380
Blown fuse or fusible link
Damaged wiring to the glow plugs
Owner notes linked to P0380: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Measure each glow plug's resistance - they should all read similarly low; the outlier is dead
Check the relay/module output during the preheat cycle Tests: Failed glow plug relay or control module
Verify the fuse or fusible link feeding the circuit Tests: Blown fuse or fusible link
Replace glow plugs as a full set - the rest are the same age and will fail soon Tests: One or more failed glow plugs (most common - they wear out like light bulbs)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2001–2012 GMC Sierra HD: Glow plug control module failure (P0380) and individual glow plugs — test first, then buy for this job.
The price range below is a national planning range for P0380 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $500
Labor$200 – $600
Diesel emissions parts are expensive; diagnosis first. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0380 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Glow plug replacement is straightforward on many diesels; some bury them under the valve cover.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →