Diagnose soonDiesel emissions-system fault. Follow the diagnostic path; some affect drivability.
The heater plugs that help your diesel start on cold mornings have an electrical fault. Expect long cranking and clouds of white smoke on cold starts.
Model notes: Always replace glow plugs as a set and use a torque wrench - they snap off in the cylinder head if overtightened or forced, turning a simple job into a nightmare.
Key facts
P0380 means glow plug/heater circuit A malfunction. The heater plugs that help your diesel start on cold mornings have an electrical fault. Expect long cranking and clouds of white smoke on cold starts. WrenchFair's published fair-price range for this repair is $100–$500 parts and $200–$600 labor at independent shops.
WrenchFair rates P0380 a 3-of-5 DIY difficulty (“Glow plug replacement is straightforward on many diesels; some bury them under the valve cover.”) with a “Diagnose soon” driveability rating: Diesel emissions-system fault. Follow the diagnostic path; some affect drivability. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2017–2026 GMC 2500 (6.6L Duramax L5P Turbo Diesel) — L5P glow plug failures - learn procedure, codes, and testing:Owner-verified
DIY-friendly with a multimeter and a scan tool that can run the glow plug learn procedure (GDS2 or capable aftermarket tool). Plugs are reached through the wheelhouse on the L5P.
Do this test first: Measure each glow plug's resistance - they should all read similarly low; the outlier is dead
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0380 on the 2017–2026 GMC 2500 — but the community-sourced L5P glow plug failures - learn procedure, codes, and testing note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Glow plug into cylinder head: verify — L5P-specific torque not published in sources used; look it up in GM SI for the year before installing.
Tips
Symptoms of dead L5P glow plugs: extended cranking in cold weather, rough idle on a cold start that smooths out as the engine warms, and white smoke at startup (unburned fuel from the cold cylinder).
The L5P-specific gotcha: after you replace a glow plug, you must run the glow plug LEARN procedure with a scan tool. Skip it and glow plug codes come right back. Also check that the Glow Plug Control Module has the latest software - some phantom codes are a GPCM software/EEPROM issue, not a bad plug.
Code map: P0380/P0381 = glow plug heater circuit (control module sees a general circuit fault); P066A-P066F = per-cylinder low/high voltage faults; P0671-P0678 = individual glow plug circuits, cylinders 1-8; P1338-P133F = glow plug offset exceeded (learn limit) codes.
Test before you throw parts: measure resistance across each plug with a multimeter. DmaxStore: under 1.8 ohms is good, 1.8 ohms or higher means replace. APEX Tech Nation: healthy L5P plugs read about 0.5-1.0 ohm; an open circuit means the element is burned through. If one plug is dead, test all eight - they see the same duty cycles and fail in clusters.
Owner evidence: iRV2 L5P owners report glow plugs in #4 and #8 replaced, and another had 2 glow plugs replaced under warranty on a 2019 3500 dually. A duramaxforum owner had 'another glow plug replaced and relearn' at the dealer at 42k miles.
Cylinder numbering for the P067x codes: Bank 1 (passenger side) is 1-3-5-7 front to back; Bank 2 (driver side) is 2-4-6-8 front to back. On installation, clean the carbon from the glow plug bore with a glow plug reaming tool so the new plug seats properly, and if a plug is seized, soak it with penetrating oil - do not force it, because a broken glow plug extraction turns a one-hour job into an eight-hour one.
Typical difficulty: Easy — based on 70 code guides for the glow repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
long cranking on cold starts
white smoke on startup
rough cold idle
glow plug light flashing
check engine light
glow plug light stays on longer than normal
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
One or more failed glow plugs (most common - they wear out like light bulbs)
Failed glow plug relay or control module 2 owner notes link this repair to P0380
Blown fuse or fusible link
Damaged wiring to the glow plugs
Owner notes linked to P0380: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Measure each glow plug's resistance - they should all read similarly low; the outlier is dead
Check the relay/module output during the preheat cycle Tests: Failed glow plug relay or control module
Verify the fuse or fusible link feeding the circuit Tests: Blown fuse or fusible link
Replace glow plugs as a full set - the rest are the same age and will fail soon Tests: One or more failed glow plugs (most common - they wear out like light bulbs)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2026 GMC 2500: L5P glow plug failures - learn procedure, codes, and testing — test first, then buy for this job.
The price range below is a national planning range for P0380 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $500
Labor$200 – $600
Diesel emissions parts are expensive; diagnosis first. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0380 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Glow plug replacement is straightforward on many diesels; some bury them under the valve cover.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →