P0370

P0370: Timing reference high resolution signal 'A'

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0370?

Can I drive with a P0370 code?

Short trips and gentle driving only, until you know the cause. Timing faults can stall the engine - fix before it leaves you stranded. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0370?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Timing faults can stall the engine - fix before it leaves you stranded.

Will P0370 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The high-resolution timing signal the computer uses for ignition timing has a fault.

Model notes: Primarily a distributor-equipped engine code.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Inspect the distributor cap and rotor Tests: Failed distributor or optical sensor (most common)
  2. Check the optical sensor and its wiring Tests: Failed distributor or optical sensor (most common)
  3. Test the high-resolution signal
  4. Replace the distributor or sensor as needed Tests: Failed distributor or optical sensor (most common)

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$80 – $300
Labor$100 – $300

Distributor or timing reference sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0370 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Distributor-era code - check the optical sensor and cap first.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →