The intake camshaft sensor on bank 2 isn't reporting reliably.
Key facts
P0346 means camshaft position sensor 'A' circuit range/performance - bank 2. The intake camshaft sensor on bank 2 isn't reporting reliably. WrenchFair's published fair-price range for this repair is $40–$120 parts and $80–$250 labor at independent shops.
WrenchFair rates P0346 a 3-of-5 DIY difficulty (“Monitor the cam signal on a scan tool.”) with a “Diagnose soon” driveability rating: Fix before it leaves you stranded. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 3 factory bulletins on file for this vehicle (mostly Electrical System, Power Train, Unknown Or Other) — see the latest ones
On your 2017–2020 Ford F-150 (3.5L EcoBoost V6) — Cam phaser (VCT) cold-start rattle — diagnosis and warranty path:Owner-verified
Diagnosis is owner-doable (cold-soak rattle test, video evidence); the actual repair is a front-cover-off dealer/specialist job — owners report ~9.7 hrs of dealer labor and roughly $3,000 without warranty. Ford's Field Service Action 21B10 was a PCM reprogram that PREVENTS the rattle, not a fix for worn phasers; Customer Satisfaction Programs 21N03/21N08 extended phaser warranty coverage on affected trucks. Check your VIN with a Ford dealer for any remaining coverage or goodwill before paying out of pocket — owners report Ford customer service covered a percentage of the cost even outside warranty.
Do this test first: Monitor the cam signal for dropouts
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0346 on the 2017–2020 Ford F-150 — but the community-sourced Cam phaser (VCT) cold-start rattle — diagnosis and warranty path note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Cam phaser / VCT unit fasteners: verify — Phaser replacement torque not confirmed from an owner-verifiable source; follow the Ford workshop manual for your model year. This is a timing-critical, front-cover-off job.
Tips
The textbook symptom per TSB 23-2143: ticking/tapping/rattle from the top front cover area on initial startup after a cold soak of 6+ hours, lasting 2–5 seconds. It is caused by worn variable camshaft timing (VCT/phaser) units whose lock pins no longer hold.
Owner quick test from the forums: do a flood-clear/WOT start (hold the gas pedal down while cranking so it doesn't fire). If the rattle disappears, it points at the phasers, not the bottom end.
Record the cold start on video with the hood open — dealers were diagnosing this from owner video, and it documents the symptom if a service advisor claims they can't reproduce it.
The 21B10 PCM reprogram only prevents the rattle; it does not fix worn phasers. If the rattle is already there, the service procedure is replacing all four VCT units plus a PCM reprogram.
Insist on the UPDATED phaser design: Ford techs warn that early replacements reused the same defective design, setting owners up for repeat jobs every 40–60k miles. Ask what part revision is going in.
The same 3.5L EcoBoost issue and TSB apply to 2018–2020 Expedition and Navigator — a platform-twin data point if you're shopping used.
One owner paid $100 under the extended warranty for a job the dealer quoted near $3,000 without it — always check VIN coverage (21N03/21N08) and Ford customer-service assistance before authorizing the repair.
While the front cover is off, timing chain, guides and tensioners are normally done at the same time — factor that into quotes rather than paying the labor twice.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
hard start
rough running
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Degrading camshaft position sensor (most common)
Damaged wiring or loose connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Monitor the cam signal for dropouts
Inspect the wiring
Replace the sensor if the signal is erratic
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2020 Ford F-150: Cam phaser (VCT) cold-start rattle — diagnosis and warranty path — test first, then buy for this job.
The price range below is a national planning range for P0346 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $120
Labor$80 – $250
Camshaft position sensor replacement (bank 2). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0346 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →