Knock sensor 2's circuit is shorted - the computer can't hear pinging on that bank.
Key facts
P0332 means knock sensor 2 circuit low. Knock sensor 2's circuit is shorted - the computer can't hear pinging on that bank. WrenchFair's published fair-price range for this repair is $30–$100 parts and $100–$300 labor at independent shops.
WrenchFair rates P0332 a 3-of-5 DIY difficulty (“Standard sensor circuit diagnosis.”) with a “Diagnose soon” driveability rating: Fix reasonably soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2000–2013 Chevrolet 2500 (6.0L Vortec V8 (LQ4/LQ9/LY6/L96)) — 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix:Owner-verified
Driveway job with patience — both sensors live in the lifter valley UNDER the intake manifold, so the intake has to come off. Budget a half day the first time.
Do this test first: Test the sensor's resistance
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0332 on the 2000–2013 Chevrolet 2500 — but the community-sourced 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Knock sensor: verify — Forum consensus is 15 ft-lb with a 22mm socket — confirm against GM service info before torquing. Over-torquing cracks the sensor; under-torquing throws the code again.
Tips
The two knock sensors sit in wells in the lifter valley UNDER the intake manifold — you cannot see, reach, or test them without pulling the intake. P0327 is the front (bank 1) sensor circuit low, P0332 the rear (bank 2). Owners routinely find the wells full of water and corrosion after pressure-washing the engine or years of car-wash runoff.
GM issued TSB 02-06-04-023A for the rear sensor's water susceptibility. The field fix owners swear by: clean and dry the wells, install new AC Delco sensors plus a new harness, and build a ~3/8-inch-wide RTV dam around each sensor cavity to divert water away. Skipping the dam is why the code comes back a month later.
Always replace the knock sensor harness with the sensors. The under-intake harness gets pinched, chafed, or oil-soaked, and a large share of 'still getting codes after new sensors' threads end at a damaged harness, not a bad sensor. Ohm new sensors before install (forum consensus 93-107k ohms) and never install one that has been dropped — it is junk.
If codes persist after sensors + harness + RTV dam, stop throwing parts: check continuity from the intake connector back to the PCM, pull the PCM connectors and look for green corrosion on the pins, and confirm the sensors are torqued to spec — incorrect torque alone sets the circuit-low codes.
Use AC Delco/GM sensors and harness. Multiple owners report aftermarket sensors failing out of the box or setting codes again within months. While the intake is off, replace the intake manifold gaskets — the Fel-Pro metal type is the forum favorite.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
reduced power under load
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Shorted knock sensor 2 (most common)
Wiring shorted to ground
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Test the sensor's resistance
Inspect for shorts to ground
Replace the sensor if shorted internally Tests: Shorted knock sensor 2 (most common)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2000–2013 Chevrolet 2500: 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix — test first, then buy for this job.
The price range below is a national planning range for P0332 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $100
Labor$100 – $300
Knock sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0332 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →