Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonMisfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving.
The engine computer has lost the RPM signal - it can't tell how fast the engine is spinning, so it can't time the spark. Expect stalling or a no-start.
VW/Audi note (VCDS): The RPM PID during cranking is the whole test: signal present means look elsewhere, no signal means the crank sensor circuit has failed.
Model notes: No RPM signal during cranking is one of the most definitive no-start diagnostics there is - if the scan tool shows zero RPM while the engine turns, the crank sensor circuit is the problem.
Key facts
P0320 means ignition/distributor engine speed input circuit malfunction. The engine computer has lost the RPM signal - it can't tell how fast the engine is spinning, so it can't time the spark. Expect stalling or a no-start. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0320 a 3-of-5 DIY difficulty (“The sensor is usually easy to replace; confirming the signal with a scope or scan tool is the skill part.”) with a “Diagnose soon” driveability rating: Misfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
stalling
no-start or hard start
tachometer dropping to zero while driving
check engine light
misfire
hesitation
lack of power
Likely causes
Failed crankshaft position sensor (most common source of the RPM signal)
Damaged crank sensor wiring or connector
Failed ignition module not producing the reference signal
Excessive air gap or damaged reluctor ring at the crank sensor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch the RPM PID on the scan tool while cranking - no RPM reading during cranking points squarely at the crank sensor circuit Tests: Damaged crank sensor wiring or connector
Check the sensor connector and wiring for damage Tests: Damaged crank sensor wiring or connector
Test sensor resistance against spec, or better, check for an AC signal while cranking with a multimeter Tests: Failed crankshaft position sensor (most common source of the RPM signal)
Inspect the reluctor ring for damaged or missing teeth if the sensor tests good Tests: Excessive air gap or damaged reluctor ring at the crank sensor
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $120
Labor$80 – $180
Camshaft/crankshaft position sensor or wiring repair is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0320 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is usually easy to replace; confirming the signal with a scope or scan tool is the skill part.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →