P0316

P0316: Engine misfire detected on startup (first 1000 revolutions)

For your specific vehicle: P0316 on a 2013–2019 Ford Escape · 2011–2019 Ford Explorer · 2020–2021 Ford F-250 · 2020–2021 Ford F-350

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The engine stumbles for the first few seconds after a cold start, then smooths out. The classic cause is a fuel injector that drips gasoline into a cylinder overnight.

VW/Audi note (VCDS): Log misfire counters during a cold start; the pattern in the first minute is far more informative than a warm-engine check.
Model notes: If the engine starts rough but smooths out within 30 seconds, suspect fuel leaking into cylinders overnight rather than ignition parts - ignition misfires usually persist when warm.

Key facts

Symptoms

Likely causes

Owner notes linked to P0316: 4 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check which cylinders misfire on startup using misfire counters - one cylinder points at its injector or plug, random points at fuel pressure or battery Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
  2. Test fuel pressure leak-down overnight: pressure that bleeds off points at a leaking injector or check valve Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
  3. Pull plugs on the offending cylinders after an overnight sit - wet plugs confirm injector leak-down Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
  4. Load-test the battery - marginal batteries cause exactly this symptom on cold mornings Tests: Weak battery or slow cranking reducing cold-start spark energy

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$30 – $120
Labor$80 – $180

Coils and spark plugs are the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0316 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Overnight leak-down testing takes patience; the diagnosis spans fuel, ignition, and mechanical causes.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →