Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHot fuel causes vapor lock and lean running - diagnose soon, and don't run the tank near empty in heat.
Your fuel is too hot - usually a struggling fuel pump or a blocked return line. Expect hesitation, stalling when hot, and hard hot restarts.
Model notes: Common on diesels where the high-pressure pump heats the fuel, and on vehicles with saddle tanks and complex return plumbing.
Key facts
P0168 means fuel temperature too high. Your fuel is too hot - usually a struggling fuel pump or a blocked return line. Expect hesitation, stalling when hot, and hard hot restarts. WrenchFair's published fair-price range for this repair is $100–$600 parts and $150–$400 labor at independent shops.
WrenchFair rates P0168 a 3-of-5 DIY difficulty (“Verify the reading is real before replacing the pump - a lying sensor is cheaper than a pump.”) with a “Diagnose soon” driveability rating: Hot fuel causes vapor lock and lean running - diagnose soon, and don't run the tank near empty in heat. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
hesitation when hot
stalling
hard hot restart
loss of power
Likely causes
Failing fuel pump running hot (most common)
Restricted fuel return line
Skewed fuel temperature sensor
Very low fuel level in extreme heat
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Verify the fuel temperature reading is plausible Tests: Skewed fuel temperature sensor
Check fuel pressure - a weak pump runs hot Tests: Failing fuel pump running hot (most common)
Inspect the fuel return line for kinks or blockage Tests: Restricted fuel return line
Keep the tank above a quarter full and retest in hot conditions
Replace the fuel pump if it's overheating and pressure is low
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $600
Labor$150 – $400
Fuel pump replacement if the pump is overheating. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0168 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Verify the reading is real before replacing the pump - a lying sensor is cheaper than a pump.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →