P0133

P0133 on a 2018–2024 Toyota Camry: O2 sensor circuit slow response, bank 1 sensor 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0133 on a 2018–2024 Toyota Camry

DIY difficulty 2/5

Can I drive with P0133?

Can I drive with a P0133 code?

Yes. P0133 doesn't make your car unsafe to drive on its own. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0133?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever.

Will P0133 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

Your oxygen sensor has gotten slow with age, like it's going hard of hearing. It still works, but the engine can't fine-tune the fuel mixture, so gas mileage drops.

Model notes: This is a wear code more than a failure code - sensors simply get slow with age and heat cycles. Replacing upstream sensors as preventive maintenance around 100k miles is common practice on high-mileage DIY vehicles.

Key facts

☑ Before you buy parts — check these first:
On your 2018–2024 Toyota Camry (2.5L 4-cyl (A25A-FKS)) — O2 (oxygen) sensors: Owner-verified
Bank 1 Sensor 1 (upstream) is a wideband air-fuel ratio sensor, not a conventional narrowband O2 — the downstream is the heated oxygen sensor (per the factory service manual's monitor description). TRQ's video walkthrough covers the upstream sensor replacement for the full 2018-2024 Camry range, demonstrated on a 2022 LE 2.5L AWD. Soak the sensor threads with rust penetrant well before the attempt — seized threads are the known pain point on these sensors.
Do this test first: Graph the sensor voltage at a steady 2500 RPM and count switches: a healthy sensor crosses 0.45V many times per second; fewer than a couple per second is lazy
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0133 on the 2018–2024 Toyota Camry — but the community-sourced O2 (oxygen) sensors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Graph the sensor voltage at a steady 2500 RPM and count switches: a healthy sensor crosses 0.45V many times per second; fewer than a couple per second is lazy
  2. Rule out exhaust leaks at the manifold and flex pipe first - leaks mimic a slow sensor Tests: Minor exhaust leak upstream of the sensor diluting the exhaust sample
  3. Check the heater circuit with a multimeter; a weak heater delays closed-loop operation Tests: Weak sensor heater making the sensor slow to reach operating temperature
  4. If the sensor is past 100k miles and lazy, replacement is the fix - cleaning does not work Tests: Aged, contaminated O2 sensor with a fouled sensing element (most common past 100k miles)

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2018–2024 Toyota Camry: O2 (oxygen) sensors — test first, then buy for this job.

Expensive fork: Catalytic converter — only if the downstream waveform shows a dead cat after a good sensor and no exhaust leak. The price range below is a national planning range for P0133 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $130
Labor$75 – $180

O2 sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0133 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Straightforward sensor replacement; there is no adjustment or cleaning that reliably restores a lazy sensor.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

🔍 Seeing multiple codes? Combinations mean something different than codes alone. How to read code combinations →
Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →