P0112: Intake air temperature sensor circuit low input
DIY difficulty 1/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonBad air measurement causes poor running and possible limp mode. Drive gently.
The air temperature sensor is shorted and telling the computer the incoming air is extremely hot. The computer cuts fuel in response and the car hesitates.
VW/Audi note (VCDS): The unplug test works on all thermistor sensors: unplugged should read the extreme cold default.
Model notes: IAT low-input codes after engine work are often pinched harnesses - recheck anything that was removed or moved during the job.
Key facts
P0112 means intake air temperature sensor circuit low input. The air temperature sensor is shorted and telling the computer the incoming air is extremely hot. The computer cuts fuel in response and the car hesitates. WrenchFair's published fair-price range for this repair is $10–$250 parts and $50–$150 labor at independent shops.
WrenchFair rates P0112 a 1-of-5 DIY difficulty (“Low input on a temperature sensor almost always means a short to ground - inspect the wiring.”) with a “Diagnose soon” driveability rating: Bad air measurement causes poor running and possible limp mode. Drive gently. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
lean hesitation
possible hot-start difficulty
engine pinging/knocking under load
Likely causes
Signal wire shorted to ground (most common)
Failed sensor with internal short
Damaged connector with terminals touching
Chafed harness grounding the signal wire
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Unplug the sensor - the reading should jump to the cold default; if it stays pinned hot, the wiring is shorted to ground Tests: Signal wire shorted to ground (most common)
Inspect the harness for chafing, especially near sharp brackets
Measure sensor resistance - near zero confirms an internally shorted sensor Tests: Signal wire shorted to ground (most common)
Repair wiring or replace the sensor as indicated
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$10 – $250
Labor$50 – $150
Cleaning is cheap; sensor replacement costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0112 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
1 of 5 — Low input on a temperature sensor almost always means a short to ground - inspect the wiring.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →