P0075

P0075 on a 2008–2013 Infiniti G37: Intake valve control solenoid circuit fault, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0075 on a 2008–2013 Infiniti G37

DIY difficulty 2/5

The electric valve controlling your intake camshaft timing on the cylinder-1 side has an electrical problem - usually a failed solenoid, blown fuse, or damaged wiring.

Model notes: Subaru's name for the VVT solenoid circuit. Pairs with P0026 (the range/performance version of the same system).

Key facts

☑ Before you buy parts — check these first:
On your 2008–2013 Infiniti G37 (3.7L VQ37VHR V6) — Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair: Owner-verified
Front of the engine - solenoids are externally accessible, so this is a diagnose-and-swap job, not a timing-cover job.
Do this test first: Check the fuse for the VVT solenoid circuit first
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0075 on the 2008–2013 Infiniti G37 — but the community-sourced Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: myg37.com 'P0021 P0011 VVT Solenoid' - G37 owner: after fixing the rear timing cover (gallery) gasket with oil pressure confirmed good, P0524 and P0021 persisted until the faulty bank 2 intake timing solenoid was replaced - both codes then cleared · myg37.com 'P0011, P0021, P0524, p0075, p0081, p0340, p0345 check before replacing gasket' - warns against jumping straight to the gallery gasket: the VTC phaser position ring can slip and IVT solenoids can fail with the same codes; FSM lists intake valve control solenoid valve among the possible causes of P0011/P0021

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check the fuse for the VVT solenoid circuit first Tests: Open or shorted wiring in the solenoid circuit
  2. Inspect the bank 1 intake solenoid connector and wiring for damage or corrosion Tests: Failed intake valve control solenoid (most common)
  3. Unplug the solenoid and measure its resistance against factory spec - open or shorted means replacement Tests: Open or shorted wiring in the solenoid circuit
  4. Check for battery voltage and a good ground/driver signal at the connector with the key on Tests: Corroded or loose connector
  5. Trace the harness back to the ECM if voltage or control signal is missing

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2008–2013 Infiniti G37: Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair — test first, then buy for this job.
The price range below is a national planning range for P0075 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $150
Labor$80 – $250

Intake valve control solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0075 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Solenoid and fuse checks are easy; the solenoid is usually right on top of the valve cover.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →