P0062

P0062: O2 sensor heater circuit fault, bank 2 sensor 3

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0062?

Can I drive with a P0062 code?

Yes. P0062 doesn't make your car unsafe to drive on its own. Emissions-monitoring only - no driveability impact. Fix before your next inspection. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0062?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions-monitoring only - no driveability impact. Fix before your next inspection.

Will P0062 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The heater inside your third oxygen sensor (bank-2 side) isn't working. It only monitors emissions equipment, so the car drives normally.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Confirm your vehicle is equipped with a bank 2 sensor 3 Tests: Failed heater element inside the bank 2 sensor 3 oxygen sensor (most common)
  2. Check the O2 heater fuse Tests: Blown fuse in the O2 heater power feed
  3. Inspect the sensor 3 wiring for heat damage
  4. Verify battery voltage at the heater feed with the key on Tests: Blown fuse in the O2 heater power feed
  5. Measure the heater element resistance against factory spec and replace the sensor if bad

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$40 – $150
Labor$80 – $180

Oxygen sensor replacement (bank 2 sensor 3). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0062 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Same diagnosis as any O2 heater code; just confirm your vehicle actually has a sensor 3 before ordering parts.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →