P0059: O2 sensor heater resistance out of range, bank 2 sensor 1
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonCold-start fueling is compromised - address it soon, since prolonged rich cold running isn't kind to the catalyst.
Your front oxygen sensor's heater (bank-2 side) is worn out and can't warm the sensor properly. Cold-start fuel control suffers until you replace the sensor.
Key facts
P0059 means o2 sensor heater resistance out of range, bank 2 sensor 1. Your front oxygen sensor's heater (bank-2 side) is worn out and can't warm the sensor properly. Cold-start fuel control suffers until you replace the sensor. WrenchFair's published fair-price range for this repair is $40–$150 parts and $80–$180 labor at independent shops.
WrenchFair rates P0059 a 2-of-5 DIY difficulty (“A resistance check with a multimeter confirms it; replacement is a standard O2 sensor job.”) with a “Diagnose soon” driveability rating: Cold-start fueling is compromised - address it soon, since prolonged rich cold running isn't kind to the catalyst. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
diminished fuel efficiency
black smoke on cold start from rich running
delayed closed-loop on bank 2
Likely causes
Degraded heater element inside the bank 2 sensor 1 O2 sensor (most common)
High-resistance connection from corroded terminals
Damaged wiring adding resistance to the heater circuit
Blown fuse or failing heater relay
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the sensor wiring and connectors near hot exhaust parts
Test the O2 heater fuse and relay under load Tests: Blown fuse or failing heater relay
With the engine cold, verify heater voltage matches battery voltage when commanded on
Unplug the sensor and measure the heater element resistance directly against factory spec; replace the sensor if it's out of range Tests: Degraded heater element inside the bank 2 sensor 1 O2 sensor (most common)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $150
Labor$80 – $180
Upstream oxygen sensor replacement (bank 2 sensor 1). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0059 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — A resistance check with a multimeter confirms it; replacement is a standard O2 sensor job.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →