P0026: Intake valve control solenoid range/performance, bank 1
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonPerformance and economy suffer; prolonged oil starvation to the actuator wears it out - address it.
Can I drive with P0026?
Can I drive with a P0026 code?
Short trips and gentle driving only, until you know the cause. Performance and economy suffer; prolonged oil starvation to the actuator wears it out - address it. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0026?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Performance and economy suffer; prolonged oil starvation to the actuator wears it out - address it.
Will P0026 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The valve controlling oil flow to your intake camshaft adjuster isn't moving the camshaft through its full range on the cylinder-1 side. Low or dirty oil is the first thing to check.
Model notes: Common Subaru code (their naming for the VVT solenoid circuit). Similar in meaning to P0027/P0028/P0029 on the other camshaft/bank.
Key facts
P0026 means intake valve control solenoid range/performance, bank 1. The valve controlling oil flow to your intake camshaft adjuster isn't moving the camshaft through its full range on the cylinder-1 side. Low or dirty oil is the first thing to check. WrenchFair's published fair-price range for this repair is $40–$200 parts and $80–$300 labor at independent shops.
WrenchFair rates P0026 a 2-of-5 DIY difficulty (“Oil service and solenoid testing are very DIY-friendly; actuator replacement goes deeper.”) with a “Diagnose soon” driveability rating: Performance and economy suffer; prolonged oil starvation to the actuator wears it out - address it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
poor acceleration or engine performance
decreased fuel economy
Likely causes
Low engine oil level or contaminated oil (most common)
Clogged oil passages or sludge restricting flow to the actuator
Malfunctioning intake valve control solenoid
Worn camshaft actuator (phaser) with internal leaks
Loose or incorrectly installed timing chain/belt
ECM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Fix any accompanying P0075/P0076/P0077 solenoid circuit codes first Tests: Malfunctioning intake valve control solenoid
Check oil level and condition - change oil and filter if dirty or low, then clear and retest
Unplug the bank 1 intake solenoid and check its resistance against factory spec Tests: Malfunctioning intake valve control solenoid
Remove the solenoid and inspect for sludge, debris, or damaged O-rings that bleed oil pressure Tests: Malfunctioning intake valve control solenoid
Watch commanded vs. actual intake camshaft angle - no movement with a good solenoid points to the actuator or timing components
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $200
Labor$80 – $300
Intake valve control solenoid replacement or engine oil service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0026 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Oil service and solenoid testing are very DIY-friendly; actuator replacement goes deeper.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →