P0021

P0021 on a 2016–2019 Mercedes-Benz GLC: Intake camshaft timing over-advanced, bank 2

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0021 on a 2008–2012 Infiniti G37 · 2008–2013 Infiniti G37 · 2016–2019 Mercedes-Benz GLC · 2012–2018 Mercedes-Benz GLE · 2007–2008 Nissan 350Z · 2009–2020 Nissan 370Z
Show all 7 vehicles with this code

2005–2010 Nissan Frontier

DIY difficulty 2/5

Can I drive with P0021?

Can I drive with a P0021 code?

Short trips and gentle driving only, until you know the cause. Stalling and hard starting make this unpleasant to live with - diagnose it soon. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0021?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Stalling and hard starting make this unpleasant to live with - diagnose it soon.

Will P0021 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

More detail: can I drive with P0021? →

Your intake camshaft timing is stuck too far advanced on the bank-2 side - usually a stuck valve in the variable valve timing system. Expect hard starting, rough idle, and stalling.

Model notes: Frequently appears with P0011 (both banks over-advanced) when oil condition is the root cause - service the oil before replacing two solenoids.

Key facts

☑ Before you buy parts — check these first:
On your 2016–2019 Mercedes-Benz GLC (2.0L M274 4-cylinder) — M274 camshaft adjuster cold-start rattle: Owner-verified
Advanced driveway job with camshaft locking tools; engine-stays-in.
Do this test first: Check oil level, condition, and viscosity; change if suspect, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0021 on the 2016–2019 Mercedes-Benz GLC — but the community-sourced M274 camshaft adjuster cold-start rattle note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum - MBWorld X253 · owner repair video - M274 camshaft replacement

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0021: 7 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check oil level, condition, and viscosity; change if suspect, then clear and retest Tests: Dirty or wrong-viscosity oil
  2. Watch commanded vs. actual bank 2 intake camshaft angle - stuck advanced with no command points to the solenoid or phaser Tests: Worn camshaft phaser stuck advanced
  3. Remove and inspect the bank 2 intake VVT solenoid for sludge or a stuck pintle; test or replace Tests: VVT oil control solenoid stuck open (most common)
  4. Check the control wiring for a short holding the solenoid on Tests: Wiring fault holding the solenoid energized
  5. Verify base camshaft timing marks if the solenoid tests good

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2016–2019 Mercedes-Benz GLC: M274 camshaft adjuster cold-start rattle — test first, then buy for this job.
The price range below is a national planning range for P0021 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $200
Labor$80 – $300

VVT oil control valve (solenoid) replacement, often with an oil change. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0021 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Solenoid replacement plus fresh oil fixes most cases; live cam-angle data confirms the diagnosis.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

🔍 Seeing multiple codes? Combinations mean something different than codes alone. How to read code combinations →
Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →