Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on.
Can I drive with P0018?
Can I drive with a P0018 code?
Short trips and gentle driving only, until you know the cause. A stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0018?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. A stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on.
Will P0018 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your engine's computer sees the intake camshaft and crankshaft out of sync on the bank-2 side. Check the sensors first (cheap), but a stretched timing chain is the classic mechanical cause.
Model notes: Bank 2 is the side opposite cylinder 1; 'A' is typically the intake camshaft.
Key facts
P0018 means crankshaft-camshaft correlation fault, bank 2 sensor A. Your engine's computer sees the intake camshaft and crankshaft out of sync on the bank-2 side. Check the sensors first (cheap), but a stretched timing chain is the classic mechanical cause. WrenchFair's published fair-price range for this repair is $40–$700 parts and $100–$2200 labor at independent shops.
WrenchFair rates P0018 a 3-of-5 DIY difficulty (“Sensor and wiring checks are easy DIY; confirming a stretched chain means opening up the timing cover.”) with a “Diagnose soon” driveability rating: A stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
reduced engine performance
hard starting or no start
rattling noise near the front of the engine
rough running
Likely causes
Stretched timing chain or a belt that skipped a tooth (most common mechanical cause) 4 owner notes link this repair to P0018
Failed timing chain/belt tensioner 4 owner notes link this repair to P0018
Crankshaft or camshaft tone ring slipped or damaged 4 owner notes link this repair to P0018
Bad crankshaft or camshaft position sensor 4 owner notes link this repair to P0018
Damaged wiring to the cam or crank sensor 4 owner notes link this repair to P0018
VVT actuator stuck off its zero-degree position
Owner notes linked to P0018: 4 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the bank 2 intake cam sensor and crank sensor wiring for damage or oil contamination Tests: Damaged wiring to the cam or crank sensor
Check for companion codes (P0008, P0009, P0016, P0017, P0019) that point at the timing chain Tests: Stretched timing chain or a belt that skipped a tooth (most common mechanical cause)
Look up service bulletins for your engine
Compare cam and crank waveforms with a scope if available - shifted patterns mean sensor or tone-ring trouble Tests: Crankshaft or camshaft tone ring slipped or damaged
Inspect timing chain/belt alignment, tensioner condition, and tone-ring security
Verify the bank 2 intake VVT actuator parks at zero degrees
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $700
Labor$100 – $2200
Camshaft or crankshaft position sensor replacement if the sensor is at fault; timing chain, tensioner, and guide replacement if the chain stretched. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0018 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Sensor and wiring checks are easy DIY; confirming a stretched chain means opening up the timing cover.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →