P0015

P0015 on a 2006–2018 BMW 3 Series: Exhaust camshaft timing over-retarded, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0015 on a 2006–2018 BMW 3 Series · 2012–2018 BMW 3 Series

DIY difficulty 2/5

Your exhaust camshaft timing can't reach the position the computer wants on the cylinder-1 side. Usually an oil-flow issue in the variable valve timing system or a stretched timing chain.

Key facts

☑ Before you buy parts — check these first:
On your 2006–2018 BMW 3 Series (N52/N54 (E90), N20/N26 (F30)) — Oil filter housing gasket replacement: Owner-verified
E90 (N52/N54): remove the airbox/intake ducting and serpentine belt, drain ~2L of coolant and loosen the filter cap so housing oil drains to the pan; the housing is held by three E10 bolts, one tucked under the intake manifold runners (reachable with a universal-joint E10 without manifold removal). F30 (N20/N26): more involved — the intake manifold, charge pipe and DME must come off to reach the housing, plus coolant drain. On both, also replace the oil cooler/heat-exchanger gasket if fitted.
Do this test first: Check oil level and condition; service with the correct viscosity, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0015 on the 2006–2018 BMW 3 Series — but the community-sourced Oil filter housing gasket replacement note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: Bentley E90 manual — oil filter housing R&R (N52/N54), torque 22 Nm · E90Post — N52 OFHG DIY (3 E10 bolts, belt protection, oil-change timing) · E90Post — oil leak onto serpentine belt warning · FCP Euro — N20/N26 OFHG DIY video (intake manifold, charge pipe, DME removal) · BavMods — OFHG failure: belt slip-off and crank-seal ingestion warning

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check oil level and condition; service with the correct viscosity, then clear and retest Tests: Dirty or wrong-viscosity oil
  2. Watch commanded vs. actual exhaust camshaft angle on bank 1 - failure to reach the target confirms it Tests: Worn camshaft phaser
  3. Remove the bank 1 exhaust VVT solenoid, inspect screens for sludge, clean or replace Tests: Clogged VVT solenoid screen or stuck-closed oil control valve
  4. Check engine oil pressure on high-mileage engines Tests: Low oil level or pressure starving the VVT phaser (most common)
  5. Evaluate timing-chain stretch and phaser wear if oil and solenoid are good

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2006–2018 BMW 3 Series: Oil filter housing gasket replacement — test first, then buy for this job.
The price range below is a national planning range for P0015 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $250
Labor$80 – $300

VVT oil control valve (solenoid) replacement or oil service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0015 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Start with oil service; the solenoid is an easy swap. Chain stretch is the deeper possibility.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →