Diagnose soonStalling and hard starting make this unpleasant to live with - diagnose it soon.
Can I drive with P0014?
Can I drive with a P0014 code?
Short trips and gentle driving only, until you know the cause. Stalling and hard starting make this unpleasant to live with - diagnose it soon. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0014?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Stalling and hard starting make this unpleasant to live with - diagnose it soon.
Will P0014 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your exhaust camshaft timing is stuck too far advanced on the cylinder-1 side - usually a stuck valve in the variable valve timing system letting oil flow when it shouldn't.
Model notes: Common on GM 2.4L Ecotec, Hyundai/Kia, Nissan. Frequently appears with P0011 on engines where both solenoids sludge up together.
Key facts
P0014 means exhaust camshaft timing over-advanced, bank 1. Your exhaust camshaft timing is stuck too far advanced on the cylinder-1 side - usually a stuck valve in the variable valve timing system letting oil flow when it shouldn't. WrenchFair's published fair-price range for this repair is $40–$200 parts and $80–$300 labor at independent shops.
WrenchFair rates P0014 a 2-of-5 DIY difficulty (“Solenoid replacement plus fresh oil fixes most cases; confirming with live cam-angle data is the key step.”) with a “Diagnose soon” driveability rating: Stalling and hard starting make this unpleasant to live with - diagnose it soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 2,692 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Engine And Engine Cooling) — see the latest ones
On your 2010–2017 Chevrolet Equinox (2.4L Ecotec I4) — VVT camshaft actuator solenoids (P0010/P0013):Owner-verified
Both solenoids sit on top of the engine under the plastic engine cover — no intake manifold removal needed. One 10mm bolt holds each unit.
Do this test first: Check oil level, condition, and viscosity; change if suspect, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0014 on the 2010–2017 Chevrolet Equinox — but the community-sourced VVT camshaft actuator solenoids (P0010/P0013) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
VVT solenoid bolt (10mm): verify — Bolt torque not confirmed from a forum source — snug by hand; confirm against factory service info before torquing.
Tips
The pattern: check-engine light with P0010/P0011 (intake) or P0013/P0014 (exhaust), sometimes with stalling or cutting out at low speeds and stoplights. Owners in the repair logs report replacing these solenoids multiple times — roughly yearly on high oil-consumption engines.
The easy electrical test before buying parts: unplug each solenoid and check resistance across the terminals — spec is 8-13 ohms. Also check for a short to ground from each terminal. Any solenoid out of spec gets replaced; a technician notes it is common for both to fail, so if one is dead, test the other.
Identification: gray connector = intake solenoid (GM 12655420), black connector = exhaust solenoid (GM 12655421). They come as a matched pair from most parts sellers and are inexpensive.
The swap: pop the engine cover, disconnect the electrical tab, remove the single 10mm bolt, and pull the solenoid straight out. Lubricate the new O-rings with fresh oil before installing so they seat without tearing.
Before condemning the solenoid on a P0011/P0014 over-advance code, check the fine filter screens on the actuator valves — clogged screens from dirty oil cause the same codes. Cleaning the screens has fixed it for some owners without new parts.
Root-cause note: these solenoids fail early on engines that burn oil or run long oil-change intervals — the same neglected-oil problem behind the timing chain and PCV issues on this engine. Fix the oil discipline or the new solenoids will follow the old ones.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
hard starting
rough idle
stalling
poor low-speed driveability
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
VVT oil control solenoid stuck open (most common)
Incorrect camshaft timing from prior timing work
Dirty or wrong-viscosity oil
Worn camshaft phaser stuck advanced
Wiring fault holding the solenoid energized
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level, condition, and viscosity; change if suspect, then clear and retest Tests: Dirty or wrong-viscosity oil
Watch commanded vs. actual exhaust camshaft angle on bank 1 - stuck advanced with no command points to the solenoid or phaser Tests: Worn camshaft phaser stuck advanced
Remove and inspect the bank 1 exhaust VVT solenoid for sludge or a stuck pintle; test or replace Tests: VVT oil control solenoid stuck open (most common)
Check the control wiring for a short holding the solenoid on Tests: Wiring fault holding the solenoid energized
Verify base camshaft timing marks if the solenoid tests good
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2010–2017 Chevrolet Equinox: VVT camshaft actuator solenoids (P0010/P0013) — test first, then buy for this job.
The price range below is a national planning range for P0014 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $200
Labor$80 – $300
VVT oil control valve (solenoid) replacement, often with an oil change. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0014 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Solenoid replacement plus fresh oil fixes most cases; confirming with live cam-angle data is the key step.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →