P0012

P0012 on a 2012–2018 BMW 3 Series: Intake camshaft timing over-retarded, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

DIY difficulty 2/5

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0012 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

Can I drive with P0012?

Can I drive with a P0012 code?

Short trips and gentle driving only, until you know the cause. Performance suffers and a stretched chain behind it can jump - don't ignore it for months. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0012?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Performance suffers and a stretched chain behind it can jump - don't ignore it for months.

Will P0012 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

Your intake camshaft timing can't advance when the computer asks it to on the cylinder-1 side. Usually an oil-flow problem in the variable valve timing system or a worn timing chain.

Model notes: Often appears with P0026/P0075-series solenoid codes - fix the solenoid circuit fault first if both are present. Platform patterns: Ford 5.4L 3V - tensioner-gasket oil bleed (watch hot-idle oil pressure; ~25 psi or lower starves the phaser); GM 2.4L Ecotec - chain guides and tensioners; Toyota - check oil condition, then the oil control valve.

Key facts

☑ Before you buy parts — check these first:
On your 2012–2018 BMW 3 Series (2.0L N20/N26 turbo 4-cylinder) — Timing chain / guide wear: Owner-verified
Front timing cover job — radiator, fan, and front accessories come off for room. Chain, guides, tensioner, and sprockets are replaced as a set; this is a full weekend for a DIYer with BMW timing tools.
Do this test first: Check oil level and condition - top up or change with the correct viscosity, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0012 on the 2012–2018 BMW 3 Series — but the community-sourced Timing chain / guide wear note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum · owner forum · owner forum

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0012: 5 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check oil level and condition - top up or change with the correct viscosity, then clear and retest Tests: Dirty or wrong-viscosity oil
  2. Watch commanded vs. actual intake camshaft angle on bank 1 under acceleration - failure to advance confirms the fault Tests: Worn camshaft phaser
  3. Remove the bank 1 intake VVT solenoid and inspect its screens for sludge; clean or replace Tests: Clogged VVT solenoid screen or stuck-closed oil control valve
  4. Check oil pressure if the engine is high-mileage - worn bearings bleed off the pressure VVT needs Tests: Low oil level or pressure starving the VVT phaser (most common)
  5. If oil and solenoid are good, check timing-chain stretch and phaser condition
Most likely job on your 2012–2018 BMW 3 Series: Timing chain / guide wear — test first, then buy for this job.
The price range below is a national planning range for P0012 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $250
Labor$80 – $2500

Two paths, very different prices: VVT oil control valve (solenoid) — the part runs $20-$165, installed $200-$1,200 at an independent shop (buy OEM; cheap aftermarket solenoids are known to cause limp mode on some Toyotas); the timing-chain path — $700+ just to inspect at a dealer teardown, $3,000+ for the repair, which is mostly labor. The ranges above span both paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

DIY difficulty

2 of 5 — Oil service first; solenoid replacement is easy. Timing-chain diagnosis is the deeper end of this code.

Parts & tools

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →