P0012 on a 2006–2018 BMW 3 Series: Intake camshaft timing over-retarded, bank 1
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
DIY difficulty 2/5
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0012 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Diagnose soonPerformance suffers and a stretched chain behind it can jump - don't ignore it for months.
Can I drive with P0012?
Can I drive with a P0012 code?
Short trips and gentle driving only, until you know the cause. Performance suffers and a stretched chain behind it can jump - don't ignore it for months. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0012?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Performance suffers and a stretched chain behind it can jump - don't ignore it for months.
Will P0012 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your intake camshaft timing can't advance when the computer asks it to on the cylinder-1 side. Usually an oil-flow problem in the variable valve timing system or a worn timing chain.
Model notes: Often appears with P0026/P0075-series solenoid codes - fix the solenoid circuit fault first if both are present. Platform patterns: Ford 5.4L 3V - tensioner-gasket oil bleed (watch hot-idle oil pressure; ~25 psi or lower starves the phaser); GM 2.4L Ecotec - chain guides and tensioners; Toyota - check oil condition, then the oil control valve.
Key facts
P0012 means intake camshaft timing over-retarded, bank 1. Your intake camshaft timing can't advance when the computer asks it to on the cylinder-1 side. Usually an oil-flow problem in the variable valve timing system or a worn timing chain. WrenchFair's published fair-price range for this repair is $40–$250 parts and $80–$2500 labor at independent shops.
WrenchFair rates P0012 a 2-of-5 DIY difficulty (“Oil service first; solenoid replacement is easy. Timing-chain diagnosis is the deeper end of this code.”) with a “Diagnose soon” driveability rating: Performance suffers and a stretched chain behind it can jump - don't ignore it for months. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 255 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Engine And Engine Cooling) — see the latest ones
On your 2006–2018 BMW 3 Series (N52/N54 (E90), N20/N26 (F30)) — Oil filter housing gasket replacement:Owner-verified
E90 (N52/N54): remove the airbox/intake ducting and serpentine belt, drain ~2L of coolant and loosen the filter cap so housing oil drains to the pan; the housing is held by three E10 bolts, one tucked under the intake manifold runners (reachable with a universal-joint E10 without manifold removal). F30 (N20/N26): more involved — the intake manifold, charge pipe and DME must come off to reach the housing, plus coolant drain. On both, also replace the oil cooler/heat-exchanger gasket if fitted.
Do this test first: Check oil level and condition - top up or change with the correct viscosity, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0012 on the 2006–2018 BMW 3 Series — but the community-sourced Oil filter housing gasket replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Oil filter housing to cylinder head (E90 N52/N54, M8): 22 Nm (16 ft-lb) — Per Bentley E90 manual, Lubrication System 119-32/33.
Oil filter housing to cylinder head (F30 N20/N26): verify — Confirm against factory service info (BMW TIS).
Tips
THE big warning: a leaking OFHG drips oil straight onto the serpentine belt. An oil-soaked belt can slip off the pulleys and get drawn past the front crankshaft seal into the engine — belt shreds can clog the oil pickup and kill the engine. Replace any oil-contaminated belt, and inspect tensioner/idler pulleys.
Drape a bag or foil over the belt and alternator before opening the housing — the gasket seals both oil AND coolant passages, so both will spill.
Schedule the job right before a planned oil change so any oil contamination gets flushed out with the change.
Clean mating surfaces with a rag and brake cleaner only — no abrasive scraping on the aluminum, it changes the surface finish and the gasket will never seal right.
Loosen the oil filter cap first so oil in the housing drains back to the pan before you unbolt anything.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
poor acceleration and lack of power
rough idle
decreased fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Low oil level or pressure starving the VVT phaser (most common) 3 owner notes link this repair to P0012
Clogged VVT solenoid screen or stuck-closed oil control valve 3 owner notes link this repair to P0012
Stretched timing chain the phaser can't take up 3 owner notes link this repair to P0012
Dirty or wrong-viscosity oil
Worn camshaft phaser 3 owner notes link this repair to P0012
Faulty camshaft position sensor (less common) 3 owner notes link this repair to P0012
Owner notes linked to P0012: 5 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition - top up or change with the correct viscosity, then clear and retest Tests: Dirty or wrong-viscosity oil
Watch commanded vs. actual intake camshaft angle on bank 1 under acceleration - failure to advance confirms the fault Tests: Worn camshaft phaser
Remove the bank 1 intake VVT solenoid and inspect its screens for sludge; clean or replace Tests: Clogged VVT solenoid screen or stuck-closed oil control valve
Check oil pressure if the engine is high-mileage - worn bearings bleed off the pressure VVT needs Tests: Low oil level or pressure starving the VVT phaser (most common)
If oil and solenoid are good, check timing-chain stretch and phaser condition
Most likely job on your 2006–2018 BMW 3 Series: Oil filter housing gasket replacement — test first, then buy for this job.
The price range below is a national planning range for P0012 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $250
Labor$80 – $2500
Two paths, very different prices: VVT oil control valve (solenoid) — the part runs $20-$165, installed $200-$1,200 at an independent shop (buy OEM; cheap aftermarket solenoids are known to cause limp mode on some Toyotas); the timing-chain path — $700+ just to inspect at a dealer teardown, $3,000+ for the repair, which is mostly labor. The ranges above span both paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →