Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe engine runs on fixed cam timing, so performance and economy suffer - fix it, but it's not a stop-driving emergency.
The electric valve that adjusts your intake camshaft timing on the cylinder-1 side has an electrical fault - usually a bad solenoid or damaged wiring. The engine runs, but with the cam timing stuck in one position.
Model notes: Very common code across Toyota, GM, Ford, Honda, VW/Audi, Hyundai. On some engines the solenoid screens clog with sludge - cleaning can work, but replacement is more reliable.
Key facts
P0010 means intake camshaft actuator circuit fault, bank 1. The electric valve that adjusts your intake camshaft timing on the cylinder-1 side has an electrical fault - usually a bad solenoid or damaged wiring. The engine runs, but with the cam timing stuck in one position. WrenchFair's published fair-price range for this repair is $40–$150 parts and $80–$250 labor at independent shops.
WrenchFair rates P0010 a 2-of-5 DIY difficulty (“The VVT solenoid is usually an accessible bolt-on part; the main work is confirming it's the solenoid and not the wiring.”) with a “Diagnose soon” driveability rating: The engine runs on fixed cam timing, so performance and economy suffer - fix it, but it's not a stop-driving emergency. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
rough running or rough idle
poor acceleration
decreased fuel economy
Likely causes
Failed VVT oil control valve (solenoid) for the bank 1 intake camshaft (most common)
Open or shorted wiring in the VVT actuator circuit, including rodent damage
Corroded or loose connector at the solenoid
Blown fuse feeding the solenoid circuit
PCM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
With the engine warm, inspect the bank 1 intake VVT solenoid wiring and connector for damage, corrosion, or loose pins, and repair as needed Tests: Failed VVT oil control valve (solenoid) for the bank 1 intake camshaft (most common)
Check the fuse feeding the VVT solenoid circuit Tests: Blown fuse feeding the solenoid circuit
Unplug the solenoid and measure its internal resistance against the factory specification - an open or shorted winding means replacement Tests: Open or shorted wiring in the VVT actuator circuit, including rodent damage
Check the harness for continuity back to the PCM and for shorts to ground or power
Command the solenoid on and off with a bi-directional scan tool if available and listen/feel for the click
Clear the code and retest; if the circuit is good and the code returns, suspect the PCM driver
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $150
Labor$80 – $250
VVT oil control valve (solenoid) replacement for the bank 1 intake camshaft. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0010 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The VVT solenoid is usually an accessible bolt-on part; the main work is confirming it's the solenoid and not the wiring.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →