P0006

P0006: Fuel shutoff valve A control circuit low

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0006?

Can I drive with a P0006 code?

Short trips and gentle driving only, until you know the cause. A fuel shutoff that can't open leaves you with a no-start - worth diagnosing before it strands you. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0006?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. A fuel shutoff that can't open leaves you with a no-start - worth diagnosing before it strands you.

Will P0006 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The wire controlling your fuel shutoff valve is shorted to ground. The valve may not open, which can mean a crank-but-no-start situation.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check the fuse for the shutoff valve circuit Tests: Shorted fuel shutoff valve solenoid winding
  2. Unplug the valve and see if the low-voltage reading clears - if it does, the valve is shorted Tests: Shorted fuel shutoff valve solenoid winding
  3. With the valve unplugged, test the control wire for continuity to ground and repair any chafed section Tests: Control wire shorted to ground (chafed harness)
  4. Measure the valve solenoid resistance against factory spec Tests: Shorted fuel shutoff valve solenoid winding
  5. Inspect connectors for moisture or corrosion bridging terminals

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$60 – $250
Labor$120 – $300

Fuel shutoff valve replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0006 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Standard short-to-ground hunting with a multimeter, but factory documentation for this rare code is hard to come by.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →