Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYour regular brakes work fine, but stability control is off, so the car won't catch a skid for you. Drive carefully on slippery roads.
A sensor that tells your car how it is moving (multi-axis acceleration sensor) isn't sending a believable signal. Your normal brakes work fine, but stability control is switched off, so the car won't help correct a skid.
Key facts
C006A means multi-axis Acceleration Sensor. A sensor that tells your car how it is moving (multi-axis acceleration sensor) isn't sending a believable signal. Your normal brakes work fine, but stability control is switched off, so the car won't help correct a skid. WrenchFair's published fair-price range for this repair is $100–$400 parts and $120–$350 labor at independent shops.
WrenchFair rates C006A a 4-of-5 DIY difficulty (“Inspection and calibration checks are DIY-friendly; replacement often needs a scan tool with a calibration routine.”) with a “Diagnose soon” driveability rating: Your regular brakes work fine, but stability control is off, so the car won't catch a skid for you. Drive carefully on slippery roads. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
stability control warning light on
abs warning light on
stability control intervenes at odd times or not at all
Likely causes
multi-axis acceleration sensor failed
wiring fault - short, open, or corroded connector
sensor loose or mounted incorrectly after a repair
sensor calibration lost after alignment or suspension work - recalibrate before replacing parts
module fault is possible but uncommon - rule out wiring, mounting, and calibration first
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Scan all modules and fix any other sensor codes first - one bad sensor can make the module distrust this one. Tests: module fault is possible but uncommon - rule out wiring, mounting, and calibration first
2. Check whether the car recently had an alignment, suspension, or collision work: lost calibration is the most common cause. Tests: sensor calibration lost after alignment or suspension work - recalibrate before replacing…
3. Inspect the multi-axis acceleration sensor mounting and connector for looseness, corrosion, or damage. Tests: multi-axis acceleration sensor failed
4. With a scan tool, read the multi-axis acceleration sensor live data and compare it to reality (straight road, level ground, wheels straight). Tests: multi-axis acceleration sensor failed
5. Run the sensor calibration or zero-point learn procedure with a scan tool that supports it.
6. If it won't calibrate or the signal stays wrong, replace the multi-axis acceleration sensor and calibrate the new one.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $400
Labor$120 – $350
A yaw or acceleration sensor replacement with calibration, roughly $250-$600 installed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C006A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Inspection and calibration checks are DIY-friendly; replacement often needs a scan tool with a calibration routine.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →