Diagnose soonYour regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads.
Your car's ABS computer found an electrical problem in the right front wheel speed sensor wiring. Your regular brakes work fine, but ABS and traction control may be disabled.
Key facts
C0040 means right Front Wheel Speed Sensor Circuit Malfunction. Your car's ABS computer found an electrical problem in the right front wheel speed sensor wiring. Your regular brakes work fine, but ABS and traction control may be disabled. WrenchFair's published fair-price range for this repair is $40–$180 parts and $90–$250 labor at independent shops.
WrenchFair rates C0040 a 3-of-5 DIY difficulty (“Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.”) with a “Diagnose soon” driveability rating: Your regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 394 factory bulletins on file for this vehicle (mostly Electrical System, Fuel System, Gasoline, Engine And Engine Cooling) — see the latest ones
On your 2018–2022 Honda Accord (1.5L turbo (L15BE)) — Front brake pads & rotors:Owner-verified
Front brakes are conventional floating-caliper single-piston (no EPB involvement on the front; the rear axle has an electronic parking brake that must be put in maintenance mode before servicing the rear). Remove the front wheel, then remove the two caliper guide-pin bolts and swing/hang the caliper off the bracket (do not hang it by the brake hose). Remove the two caliper bracket bolts to free the bracket. The rotor is held by Honda's two small set screws (JIS — not Phillips — heads): use an impact screwdriver with a #3 bit set to counter-clockwise, or carefully chisel the heads free if corroded. Replace the screws on reassembly (they center the rotor on the studs); rust-belt cars often have them fused — anti-seize on new screws helps next time. Clean and regrease the slide pins with high-temp caliper grease during service. Pump the brake pedal to seat the pads before driving.
Do this test first: 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0040 on the 2018–2022 Honda Accord — but the community-sourced Front brake pads & rotors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Wheel lug nuts: 80 ft-lb (108 N-m) — Accord lug-nut torque cited by long-time Honda owners on driveaccord/odyclub; star pattern.
Caliper bracket bolts: verify — Confirm against 10th-gen factory service info. Older-gen Accord I4 owner threads (tonyajoy driveaccord citation) quote 79-80 ft-lb for bracket bolts; not confirmed for this generation.
Caliper guide-pin bolts: verify — Confirm against 10th-gen factory service info. Older-gen Accord I4 threads quote 26 ft-lb front / 17 ft-lb rear; not confirmed for this generation. Hold the pin with a second wrench while torquing.
Rotor set screws: verify — Confirm against 10th-gen factory service info. Honda service-manual value quoted on driveaccord for the 6x1.0 screws is 7.2 ft-lb; generation differs.
Tips
The two rotor set screws are JIS heads, not Phillips — a Phillips driver cams out and strips them; use a JIS bit or impact screwdriver.
Do not leave the set screws out: owners report a faint low-speed knock develops when the rotor can shift on the studs (stud holes are slightly oversized).
Bed the new pads/rotors per NAPA's break-in bulletin: ~15 moderate stops from 35-40 mph down to ~5 mph with ~30 sec cooling between stops; avoid panic/hard stops for the first ~200 miles so pad material transfers evenly and doesn't glaze.
Grease the slide pins and pad contact points with caliper-specific high-temp grease; torn pin boots let moisture in and cause uneven pad wear.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
abs warning light on
traction control or stability control light on
cruise control stops working
speedometer may read wrong
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed wheel speed sensor (most common)
wiring break or chafing at the wheel-arch flex point
corroded or loose sensor connector
damaged tone ring
ABS module failure is possible but uncommon - rule out wiring and sensors first
Owner notes linked to C0040: 28 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
2. Watch the right front wheel speed in ABS live data at low speed. A dead, jumpy, or mismatched reading confirms the problem corner. Tests: failed wheel speed sensor (most common)
3. Unplug the right front sensor and inspect the connector for corrosion, moisture, or bent pins. Tests: corroded or loose sensor connector
4. Trace the sensor harness along the wheel-arch flex point and look for chafing, cracks, or breaks. Tests: wiring break or chafing at the wheel-arch flex point
5. Inspect the tone ring for cracked or missing teeth while the wheel is off.
6. If the wiring and tone ring check out, replace the right front wheel speed sensor — it is the most common fix.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2018–2022 Honda Accord: Front brake pads & rotors — test first, then buy for this job.
Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors.
The price range below is a national planning range for C0040 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $180
Labor$90 – $250
A wheel speed sensor replacement, often $150-$350 installed at an independent shop. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0040 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →