U354F: Hydrogen Tank C Temperature Sensor 2 Circuit
DIY difficulty 5/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car may limit power or refuse to start; fuel cell and hydrogen work is never DIY.
A sensor in your hydrogen fuel cell system isn't reading correctly. This is specialized equipment found only on hydrogen cars - diagnosis and repair is a dealer job.
Model notes: Hydrogen fuel-cell vehicles only (e.g. Toyota Mirai, Hyundai Nexo).
Key facts
U354F means hydrogen Tank C Temperature Sensor 2 Circuit. A sensor in your hydrogen fuel cell system isn't reading correctly. This is specialized equipment found only on hydrogen cars - diagnosis and repair is a dealer job. WrenchFair's published fair-price range for this repair is $230–$2300 parts and $150–$850 labor at independent shops.
WrenchFair rates U354F a 5-of-5 DIY difficulty (“Hydrogen fuel cell systems run at extreme pressures and voltages - service is for trained, certified technicians only.”) with a “Diagnose soon” driveability rating: The car may limit power or refuse to start; fuel cell and hydrogen work is never DIY. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
fuel cell system warning
reduced power or limp mode
car won't start
check engine light
Likely causes
Failed hydrogen tank C temperature sensor 2 (most common)
Wiring or connector fault in the sensor circuit
Corrosion at the sensor connector
Control module fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code and the sensor's live data with a fuel-cell-capable scan tool.
Inspect the sensor connector for corrosion, damage, or loose pins. Tests: Corrosion at the sensor connector
Check the sensor wiring for chafing or opens per the factory diagram. Tests: Wiring or connector fault in the sensor circuit
Test the sensor per the factory procedure - compare its reading against the expected value.
Replace the sensor if it tests bad, clear the code, and confirm the reading is plausible.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$230 – $2300
Labor$150 – $850
Fuel cell sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U354F ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Hydrogen fuel cell systems run at extreme pressures and voltages - service is for trained, certified technicians only.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →