Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAn output stuck on drains the battery; an output stuck off can kill fuel, spark, or dash power - either way, don't ignore it.
Your car's computer controls a power feed that turns on with the key in the off, on, or start position, and that feed isn't switching correctly. The circuits it powers may be dead - or stuck on and draining the battery.
Key facts
U302C means ignition Output Off/On/Start. Your car's computer controls a power feed that turns on with the key in the off, on, or start position, and that feed isn't switching correctly. The circuits it powers may be dead - or stuck on and draining the battery. WrenchFair's published fair-price range for this repair is $45–$460 parts and $75–$350 labor at independent shops.
WrenchFair rates U302C a 3-of-5 DIY difficulty (“The relay and fuse checks take minutes with the fuse box diagram; wiring faults take longer but follow the same steps as any power feed.”) with a “Diagnose soon” driveability rating: An output stuck on drains the battery; an output stuck off can kill fuel, spark, or dash power - either way, don't ignore it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
circuits dead with the key in the affected position
circuits staying powered after key off
battery draining overnight
blown fuse that keeps blowing again
Likely causes
Failed ignition output relay with worn or stuck contacts (most common - swap-test first)
Blown fuse on the ignition Off/On/Start output feed
Stuck relay contacts keeping the output powered with the key off
Wiring fault or short in the output circuit
Module output driver failure (rare - test the relay and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Find the ignition Off/On/Start output relay and fuse in the fuse box diagram. Tests: Blown fuse on the ignition Off/On/Start output feed
Swap the relay with an identical one - if the fault moves, replace the relay. Tests: Failed ignition output relay with worn or stuck contacts (most common - swap-test first)
Test the output fuse and check whether the output feed is present with the key in the off, on, or start position and absent with the key off. Tests: Blown fuse on the ignition Off/On/Start output feed
If the relay and fuse are good, trace the output wiring for shorts or opens. Tests: Wiring fault or short in the output circuit
If wiring, relay, and fuse all test good, the module's output driver is suspect.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$45 – $460
Labor$75 – $350
Ignition output relay or fuse replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U302C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The relay and fuse checks take minutes with the fuse box diagram; wiring faults take longer but follow the same steps as any power feed.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →