Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA bad ignition signal can leave you with a car that won't crank - diagnose it in the driveway, not in a parking lot at night.
A wire that tells your car's computer the key is in the on position isn't sending the right signal. The car may not start, or accessories may behave as if the key were somewhere it isn't.
Key facts
U300E means ignition Input On. A wire that tells your car's computer the key is in the on position isn't sending the right signal. The car may not start, or accessories may behave as if the key were somewhere it isn't. WrenchFair's published fair-price range for this repair is $45–$460 parts and $75–$350 labor at independent shops.
WrenchFair rates U300E a 3-of-5 DIY difficulty (“Accessing the ignition switch usually means pulling steering-column trim; the electrical tests themselves are simple multimeter work.”) with a “Diagnose soon” driveability rating: A bad ignition signal can leave you with a car that won't crank - diagnose it in the driveway, not in a parking lot at night. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
no crank with the key in the affected position
dash lights behaving wrong for the key position
accessories dead or stuck on
car starts then immediately dies
multiple ignition-related codes together
Likely causes
Worn ignition switch contacts for the On position (most common)
Blown fuse or open wire on the ignition On input feed
Corroded or loose connector at the ignition switch or at the module
Ignition switch connector backing out from heat cycles
Module input fault (rare - the switch and wiring are almost always the cause)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check the battery and charging system first - low system voltage skews ignition input readings. Tests: Blown fuse or open wire on the ignition On input feed
Back-probe the ignition On input wire at the module and watch it while slowly moving the key through every position. Tests: Blown fuse or open wire on the ignition On input feed
If the signal is missing or flickers, test the same wire at the ignition switch - a clean signal at the switch with a bad one at the module means a wiring fault between them. Tests: Module input fault (rare - the switch and wiring are almost always the cause)
Inspect the ignition switch connector for heat damage, corrosion, or loose terminals. Tests: Corroded or loose connector at the ignition switch or at the module
Replace the switch if its On output is missing or erratic, clear the code, and verify every key position reads correctly.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$45 – $460
Labor$75 – $350
Ignition switch replacement or ignition input wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U300E ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Accessing the ignition switch usually means pulling steering-column trim; the electrical tests themselves are simple multimeter work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →