U0665: Lost communication with fuel rail pressure sensor bank 2
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHigh-pressure fueling is running blind on a backup map — get it fixed before towing or heavy loads, and never open fuel fittings on a running engine.
Your engine's fuel system runs at very high pressure, and a sensor on the fuel rail keeps watch over it. The computer can't talk to that sensor anymore, so it runs on a safe backup plan. Expect a check engine light and possibly reduced power.
Key facts
U0665 means lost communication with fuel rail pressure sensor bank 2. Your engine's fuel system runs at very high pressure, and a sensor on the fuel rail keeps watch over it. The computer can't talk to that sensor anymore, so it runs on a safe backup plan. Expect a check engine light and possibly reduced power. WrenchFair's published fair-price range for this repair is $100–$300 parts and $120–$250 labor at independent shops.
WrenchFair rates U0665 a 3-of-5 DIY difficulty (“High-pressure fuel fittings need care — relieve pressure before touching anything and don't reuse crush washers.”) with a “Diagnose soon” driveability rating: High-pressure fueling is running blind on a backup map — get it fixed before towing or heavy loads, and never open fuel fittings on a running engine. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduced engine power
hard starting
rough running under load
limp mode
Likely causes
failed fuel rail pressure sensor
corroded or loose sensor connector
damaged wiring near the hot fuel rail
low system voltage
engine computer communication fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Find the rail pressure sensor on the bank 2 fuel rail and inspect its connector for corrosion or heat damage. Tests: failed fuel rail pressure sensor
Check the sensor's live rail-pressure reading on a scan tool during cranking — no data means the sensor or its wiring is down. Tests: failed fuel rail pressure sensor
Trace the wiring harness away from the rail, looking for melted insulation or chafing against hot parts. Tests: damaged wiring near the hot fuel rail
Relieve fuel system pressure, replace the sensor if wiring is sound, and torque the new sensor to spec. Tests: failed fuel rail pressure sensor
Clear the code and verify rail pressure readings respond to throttle before driving.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $300
Labor$120 – $250
Replacing the fuel rail pressure sensor. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U0665 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — High-pressure fuel fittings need care — relieve pressure before touching anything and don't reuse crush washers.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →