U0592: Invalid Data Received From Gear Shift Control Module B
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonBad data from the gear shifter module can trigger reduced power or stalling — get it diagnosed before a long trip.
Your car has a dozen-plus small computers that constantly share data. The gear shifter module is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can make the car run badly, shift harshly, or lose power.
Key facts
U0592 means invalid Data Received From Gear Shift Control Module B. Your car has a dozen-plus small computers that constantly share data. The gear shifter module is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can make the car run badly, shift harshly, or lose power. WrenchFair's published fair-price range for this repair is $600–$1500 parts and $200–$400 labor at independent shops.
WrenchFair rates U0592 a 2-of-5 DIY difficulty (“Checking the battery, connectors, and wiring is solid DIY work; condemning or replacing the module itself usually isn't.”) with a “Diagnose soon” driveability rating: Bad data from the gear shifter module can trigger reduced power or stalling — get it diagnosed before a long trip. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduced power or limp mode
harsh or delayed shifting
other modules log the same code
stalling or hard starting in severe cases
Likely causes
weak battery or failing alternator corrupting network data
corroded or loose connector at the gear shifter module
damaged wiring or poor ground to the gear shifter module
a sensor feeding the gear shifter module reporting bad values
software/calibration mismatch after a repair
internal fault in the gear shifter module
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Test the battery and charging system first — low or unstable voltage is the most common cause of garbage data on the network. Tests: weak battery or failing alternator corrupting network data
Scan every module on the vehicle and record all codes; pay special attention to any faults the gear shifter module reports about itself or its own sensors. Tests: a sensor feeding the gear shifter module reporting bad values
Inspect the gear shifter module's connector and wiring for corrosion, loose or pushed-back pins, water intrusion, or rodent damage, and verify its power and ground feeds. Tests: corroded or loose connector at the gear shifter module
Clear all codes, drive normally, and rescan — if this code returns together with the gear shifter module's own sensor or input codes, fix those inputs first, since bad data in means bad data out. Tests: a sensor feeding the gear shifter module reporting bad values
If power, ground, and wiring all test good and the gear shifter module keeps broadcasting implausible values, the module itself is suspect — replacement or reprogramming is usually a dealer or specialist job.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$600 – $1500
Labor$200 – $400
Repairing the wiring or connector at the gear shifter module, or replacing the module. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U0592 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Checking the battery, connectors, and wiring is solid DIY work; condemning or replacing the module itself usually isn't.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →