U049C: Invalid Data Received From Battery Charger Control Module A
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHigh-voltage system faults can disable the vehicle — have it checked promptly, by a specialist.
Your car has a dozen-plus small computers that constantly share data. The high-voltage battery charger module is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can shut down the hybrid or electric drive.
Key facts
U049C means invalid Data Received From Battery Charger Control Module A. Your car has a dozen-plus small computers that constantly share data. The high-voltage battery charger module is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can shut down the hybrid or electric drive. WrenchFair's published fair-price range for this repair is $800–$2500 parts and $300–$600 labor at independent shops.
WrenchFair rates U049C a 4-of-5 DIY difficulty (“High-voltage components are strictly dealer/specialist work — DIY diagnosis stops at the 12v system and the scan tool.”) with a “Diagnose soon” driveability rating: High-voltage system faults can disable the vehicle — have it checked promptly, by a specialist. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
hybrid/ev system warning light on
reduced power or turtle mode
vehicle may not start or may shut down
other modules log the same code
Likely causes
weak or failing 12v auxiliary battery
corroded connector or poor ground at the high-voltage battery charger module
damaged wiring to the high-voltage battery charger module
software mismatch after a repair or update
internal fault in the high-voltage battery charger module (high-voltage work — specialist only)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Test the battery and charging system first — low or unstable voltage is the most common cause of garbage data on the network. Tests: corroded connector or poor ground at the high-voltage battery charger module
Scan every module on the vehicle and record all codes; pay special attention to any faults the high-voltage battery charger module reports about itself or its own sensors. Tests: internal fault in the high-voltage battery charger module (high-voltage work — specialist…
Inspect the high-voltage battery charger module's connector and wiring for corrosion, loose or pushed-back pins, water intrusion, or rodent damage, and verify its power and ground feeds. Tests: corroded connector or poor ground at the high-voltage battery charger module
Clear all codes, drive normally, and rescan — if this code returns together with the high-voltage battery charger module's own sensor or input codes, fix those inputs first, since bad data in means bad data out. Tests: corroded connector or poor ground at the high-voltage battery charger module
If the 12v system, wiring, and connectors all test good and the high-voltage battery charger module keeps broadcasting implausible values, the module is suspect — replacement is dealer/specialist-only high-voltage work. Never open orange-cabled housings yourself.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$800 – $2500
Labor$300 – $600
Replacing the high-voltage battery charger module (high-voltage work — specialist only). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U049C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — High-voltage components are strictly dealer/specialist work — DIY diagnosis stops at the 12v system and the scan tool.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →