P2EA3: Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 6
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe computer runs exhaust protection on backup values - fix it before towing or hard driving in heat.
The exhaust temperature sensor furthest downstream - bank 1 sensor 6 - is reading wrong. These sensors live in brutal heat and fail often.
Key facts
P2EA3 means exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 6. The exhaust temperature sensor furthest downstream - bank 1 sensor 6 - is reading wrong. These sensors live in brutal heat and fail often. WrenchFair's published fair-price range for this repair is $80–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P2EA3 a 2-of-5 DIY difficulty (“The diagnosis is easy; the sensor itself is often seized in the exhaust and needs heat and patience to remove.”) with a “Diagnose soon” driveability rating: The computer runs exhaust protection on backup values - fix it before towing or hard driving in heat. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
dpf regen behaving oddly
sensor reading stuck or jumping
reduced power under sustained load
Likely causes
Failed EGT sensor from heat cycling (most common)
Heat-damaged wiring to the sensor
Corroded connector
Soot-fouled sensor tip reading slow or biased
temperature sensor failed
wiring or connector fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code and log the sensor's reading cold - it should read near ambient. Tests: Soot-fouled sensor tip reading slow or biased
Compare it against the other EGT sensors; the outlier is the liar.
Inspect the sensor's wiring for heat damage and the connector for corrosion. Tests: wiring or connector fault
Replace the sensor if its cold reading is wrong or it does not track the others when hot. Tests: Soot-fouled sensor tip reading slow or biased
Clear the code and verify the reading tracks the other sensors on a drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $250
Labor$100 – $300
Exhaust gas temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2EA3 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The diagnosis is easy; the sensor itself is often seized in the exhaust and needs heat and patience to remove.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →