P2E69: System Too Rich During Cylinder Deactivation Bank 1
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLean running under load can overheat catalysts and valves - diagnose it rather than driving for months on it.
Your engine shuts down cylinders to save fuel, and while running in that mode on bank 1 the mixture is too rich. The problem hides when all cylinders are firing.
Key facts
P2E69 means system Too Rich During Cylinder Deactivation Bank 1. Your engine shuts down cylinders to save fuel, and while running in that mode on bank 1 the mixture is too rich. The problem hides when all cylinders are firing. WrenchFair's published fair-price range for this repair is $100–$800 parts and $150–$400 labor at independent shops.
WrenchFair rates P2E69 a 3-of-5 DIY difficulty (“Fuel-trim diagnosis is scan-tool work; the deactivation hardware itself is inside the engine.”) with a “Diagnose soon” driveability rating: Lean running under load can overheat catalysts and valves - diagnose it rather than driving for months on it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
rough running in eco/deactivation mode
worse fuel economy than expected
hesitation under light load
increased fuel consumption
black smoke from exhaust on acceleration
Likely causes
Vacuum leak unmasked during deactivation (most common for lean)
Leaking injector or high fuel pressure (most common for rich)
Deactivation lifter or solenoid not fully switching
Exhaust leak ahead of the O2 sensor skewing trims
Aging O2 sensor reading biased
injector leak on active cylinders
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with freeze-frame data and confirm it sets during deactivation mode. Tests: Vacuum leak unmasked during deactivation (most common for lean)
Log fuel trims in both full and deactivation modes - the split tells you where the error lives. Tests: Vacuum leak unmasked during deactivation (most common for lean)
For lean codes, smoke-test the intake for vacuum leaks, especially around the deactivation hardware. Tests: Vacuum leak unmasked during deactivation (most common for lean)
For rich codes, check fuel pressure and injector sealing on that bank. Tests: Leaking injector or high fuel pressure (most common for rich)
Verify the deactivation lifters/solenoids themselves are operating - a cylinder not fully deactivating skews everything.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $800
Labor$150 – $400
Intake leak repair or fuel system diagnosis and repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2E69 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Fuel-trim diagnosis is scan-tool work; the deactivation hardware itself is inside the engine.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →