Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car protects itself by limiting power, but a weakening pack only gets worse - get it diagnosed before winter.
When the car is cold, it cannot make the driving torque the computer expects. Something in the hybrid drive system is underperforming until it warms up.
Key facts
P2D28 means cold Start Propulsion Torque Performance. When the car is cold, it cannot make the driving torque the computer expects. Something in the hybrid drive system is underperforming until it warms up. WrenchFair's published fair-price range for this repair is $300–$2500 parts and $300–$600 labor at independent shops.
WrenchFair rates P2D28 a 4-of-5 DIY difficulty (“Reading hybrid torque and battery PIDs is scan-tool work for a hybrid-capable tool; interpreting them takes experience.”) with a “Diagnose soon” driveability rating: The car protects itself by limiting power, but a weakening pack only gets worse - get it diagnosed before winter. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
reduced power on cold starts
hybrid system warning light on
engine running more than usual to compensate
symptoms fade as the car warms up
Likely causes
Weak or imbalanced high-voltage battery, worst when cold (most common)
Failed battery pack heater
Biased temperature sensor skewing the torque calculation
Outdated hybrid control software
Motor or inverter derate (diagnose last)
increased cold-engine drag torque
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
High-voltage safety first: this code lives in the high-voltage system, which can carry lethal voltage. Only touch it if you are trained and equipped for HV service (insulated tools, HV gloves, service-plug procedure); everyone else should stop at scanning and hand the repair to a qualified EV/hybrid technician. Tests: Weak or imbalanced high-voltage battery, worst when cold (most common)
Scan all hybrid/EV modules and record battery temperatures, state of charge, and available torque PIDs. Tests: Biased temperature sensor skewing the torque calculation
Check whether the battery heater is working - a failed heater leaves the pack cold and weak. Tests: Failed battery pack heater
Look at battery health and cell balance data; a weak or imbalanced pack sags most when cold. Tests: Weak or imbalanced high-voltage battery, worst when cold (most common)
Check for software updates or technical service bulletins for cold-start torque calibration.
If the pack is healthy and warm but torque still falls short, the motor or inverter needs deeper diagnosis.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$300 – $2500
Labor$300 – $600
Battery heater repair or battery health diagnosis and module service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2D28 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Reading hybrid torque and battery PIDs is scan-tool work for a hybrid-capable tool; interpreting them takes experience.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →