Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonMisfiring cylinders dump raw fuel into the exhaust and can destroy the catalyst fast - do not drive far on this code.
Your direct-injection system boosts voltage to fire the injectors, and the computer cannot verify that voltage on injector group B. Expect misfires or a no-start. Usually the boost circuit, its wiring, or the driver module.
Key facts
P2C26 means fuel Injector Group B Supply Sense Circuit. Your direct-injection system boosts voltage to fire the injectors, and the computer cannot verify that voltage on injector group B. Expect misfires or a no-start. Usually the boost circuit, its wiring, or the driver module. WrenchFair's published fair-price range for this repair is $150–$800 parts and $200–$500 labor at independent shops.
WrenchFair rates P2C26 a 4-of-5 DIY difficulty (“High-voltage injection circuits - diagnose carefully with the service manual; some systems hold charge.”) with a “Diagnose soon” driveability rating: Misfiring cylinders dump raw fuel into the exhaust and can destroy the catalyst fast - do not drive far on this code. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
misfires on group b cylinders
hard starting or no-start
loss of power
Likely causes
Failed injector driver boost circuit or module (most common)
Damaged wiring or corroded connector in the supply sense circuit
Shorted injector dragging the group supply down
Control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor. - identify which cylinders are in group B and check for injector circuit codes too. Tests: Failed injector driver boost circuit or module (most common)
Inspect the injector group B wiring, connectors, and the driver module. Tests: Failed injector driver boost circuit or module (most common)
Test the injector supply/boost voltage per the factory service manual. Tests: Failed injector driver boost circuit or module (most common)
Repair the wiring or replace the faulty injector/driver module, clear the code, and confirm clean running. Tests: Failed injector driver boost circuit or module (most common)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $800
Labor$200 – $500
Injector driver module or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2C26 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — High-voltage injection circuits - diagnose carefully with the service manual; some systems hold charge.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →