P2AD3: Throttle/Pedal Position Sensor/Switch A/G Voltage Correlation
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLimp mode can leave you slow in traffic - diagnose it before a highway trip, and do not ignore a throttle you cannot trust.
Your car double-checks the gas pedal and throttle against each other, and two of those sensors disagreed. Expect reduced power or a limp mode - the computer will not trust a throttle it cannot verify. Usually one of the sensors or a wiring fault.
Key facts
P2AD3 means throttle/Pedal Position Sensor/Switch A/G Voltage Correlation. Your car double-checks the gas pedal and throttle against each other, and two of those sensors disagreed. Expect reduced power or a limp mode - the computer will not trust a throttle it cannot verify. Usually one of the sensors or a wiring fault. WrenchFair's published fair-price range for this repair is $50–$400 parts and $100–$300 labor at independent shops.
WrenchFair rates P2AD3 a 3-of-5 DIY difficulty (“Live-data detective work first; the fix is usually a sensor or assembly swap.”) with a “Diagnose soon” driveability rating: Limp mode can leave you slow in traffic - diagnose it before a highway trip, and do not ignore a throttle you cannot trust. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduced engine power / limp mode
throttle response odd or delayed
possible stalling
Likely causes
Failing sensor in the A/G pair (most common - check live data to see which one disagrees)
Damaged wiring or corroded connector in the throttle/pedal circuit
Faulty 5-volt reference shared by the sensors
Control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor. Tests: Faulty 5-volt reference shared by the sensors
Watch all throttle and pedal position sensors in live data while slowly pressing the pedal - the odd one out in the A/G pair is the liar. Tests: Failing sensor in the A/G pair (most common - check live data to see which one disagrees)
Inspect the throttle body and pedal wiring and connectors. Tests: Damaged wiring or corroded connector in the throttle/pedal circuit
Check the 5-volt reference voltage to the sensors. Tests: Faulty 5-volt reference shared by the sensors
Replace the faulty sensor (or throttle body / pedal assembly as applicable), clear the code, and confirm all sensors agree through the full pedal travel.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $400
Labor$100 – $300
Throttle or pedal position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2AD3 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Live-data detective work first; the fix is usually a sensor or assembly swap.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →