P2A39

P2A39: O2 sensor positive current control circuit circuit low b1 sensor 3

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Your car uses a wideband oxygen sensor on bank 1 (the side of the engine with cylinder 1) that the computer steers with a tiny electric current to measure the air-fuel ratio precisely. The control circuit for that current has an electrical fault (circuit low), so the computer set this code and is running that bank on a backup strategy. The sensor or its wiring needs attention.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
  2. Inspect the bank 1 (the side of the engine with cylinder 1) sensor 3 harness from the sensor to the firewall for heat damage, chafing, or melted spots. Tests: Failed wideband oxygen sensor on bank 1 (the side of the engine with cylinder 1) sensor 3…
  3. Unplug the sensor and check the connector for corrosion, pushed-back pins, and exhaust-heat discoloration; compare the sensor's heater and pump circuits against the other bank per the service manual. Tests: Damaged wiring or corroded connector in the positive current control circuit (chafing…
  4. If the wiring is sound, replace the sensor - on wideband circuits the sensor itself is the usual failure. Tests: Failed wideband oxygen sensor on bank 1 (the side of the engine with cylinder 1) sensor 3…
  5. Clear the code and confirm the sensor reads plausibly in live data on a test drive.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$60 – $300
Labor$80 – $200

Wideband oxygen sensor replacement (bank 1 sensor 3). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2A39 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Wideband sensors cost more than old-style ones, but the swap itself is the same basic hand-tool job once the wiring is ruled out.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →