Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHarsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild.
One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect slipping, harsh shifts, overheating, or the transmission stuck in a protective limp mode until it's fixed.
Key facts
P2816 means pressure Control Solenoid H Malfunction. One of the electric valves that controls your transmission's hydraulic pressure isn't doing what the computer tells it. Expect slipping, harsh shifts, overheating, or the transmission stuck in a protective limp mode until it's fixed. WrenchFair's published fair-price range for this repair is $80–$450 parts and $250–$700 labor at independent shops.
WrenchFair rates P2816 a 4-of-5 DIY difficulty (“Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.”) with a “Diagnose soon” driveability rating: Harsh shifts and limp mode overheat the fluid quickly, and overheated fluid kills transmissions - keep driving short and gentle, because a delayed solenoid fix can turn into a rebuild. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
transmission in limp mode (stuck in one gear)
slipping between shifts
hard or banging shifts
transmission overheating
worse fuel economy
Likely causes
defective pressure control solenoid H
dirty or degraded transmission fluid
clogged transmission filter starving the solenoid of flow
corroded or damaged connector at the transmission
restricted hydraulic passages or a faulty valve body
failing transmission pump (rule out fluid and solenoid first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Research TSBs for your year, model, and transmission - some solenoid codes are known issues with a published fix. Tests: clogged transmission filter starving the solenoid of flow
2. Check the transmission fluid level and condition; burnt, dark, or glittery fluid is a common root cause. Tests: dirty or degraded transmission fluid
3. Inspect the transmission and pcm connectors and all solenoid wiring for corrosion, damage, and loose pins. Tests: clogged transmission filter starving the solenoid of flow
4. With a scan tool, watch solenoid H commanded vs. actual state and line pressure during a drive - no response points at the solenoid, a wrong response points at hydraulics. Tests: defective pressure control solenoid H
5. If the circuit is good, the pan comes off: inspect the solenoid, its filter screen, and the valve body for debris or sticking valves.
6. Replace the faulty solenoid (with fresh fluid and a new filter while the pan is off), clear the code, and verify pressure control on a test drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $450
Labor$250 – $700
Replacing the faulty pressure control solenoid H, usually with fresh fluid and a new filter while the pan is off. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2816 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Diagnosis is DIY-friendly with a scan tool and multimeter, but the repair usually means dropping the transmission pan and sometimes the valve body.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →