P2804: Transmission Range Sensor B Circuit Intermittent
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA wrong or missing gear-position signal can mean a no-start, a start in gear, or the transmission stuck in limp mode - diagnose it promptly and don't drive if the dash indicator disagrees with the shifter.
Your car isn't sure which gear you've selected, because the backup gear-position sensor is sending a bad signal. You might not be able to start it, or it might only start in neutral.
Key facts
P2804 means transmission Range Sensor B Circuit Intermittent. Your car isn't sure which gear you've selected, because the backup gear-position sensor is sending a bad signal. You might not be able to start it, or it might only start in neutral. WrenchFair's published fair-price range for this repair is $40–$180 parts and $100–$300 labor at independent shops.
WrenchFair rates P2804 a 3-of-5 DIY difficulty (“An external range sensor is a straightforward driveway replacement; an internal valve-body sensor means dropping the pan and is shop work.”) with a “Diagnose soon” driveability rating: A wrong or missing gear-position signal can mean a no-start, a start in gear, or the transmission stuck in limp mode - diagnose it promptly and don't drive if the dash indicator disagrees with the shifter. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
gear indicator disagrees with the shifter
erratic or delayed shifts
backup lights not working
starts only in neutral
Likely causes
loose or fretted pins in the range sensor connector
wiring harness flexing and breaking down where it moves with the shift linkage
range sensor B loose on its mount
moisture intrusion in the external sensor or connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Pull up freeze-frame data to see the conditions when the code set, then wiggle-test the range sensor connector and harness while watching the gear-position PID. Tests: loose or fretted pins in the range sensor connector
2. Look closely for fretted, spread, or green-corroded pins - intermittent codes live in connectors. Tests: loose or fretted pins in the range sensor connector
3. Flex the harness along the shift linkage while a helper watches the PID for dropouts. Tests: wiring harness flexing and breaking down where it moves with the shift linkage
4. Clean and re-pin the connector, secure the harness so it can't rub, and re-test; replace the sensor if the dropout follows it. Tests: loose or fretted pins in the range sensor connector
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $180
Labor$100 – $300
Replacing an external transmission range sensor, including adjustment. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2804 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — An external range sensor is a straightforward driveway replacement; an internal valve-body sensor means dropping the pan and is shop work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →