P2770

P2770: Torque Converter Clutch Circuit High

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The torque converter clutch circuit has high voltage - the lock-up clutch cannot engage, hurting fuel economy.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 8 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check the transmission wiring harness for damage or loose connections; use a factory wiring diagram to locate the power source and all connection points. Tests: Wiring harness to transmission damaged, loose connection, open or shorted circuit
  2. Disconnect the transmission harness at the transmission connector, power source, and TCM; check continuity of the internal transmission wiring by locating the + and - pins for the TCC solenoid. Tests: Wiring harness to transmission damaged, loose connection, open or shorted circuit
  3. With the DVOM set to ohms, check resistance on the TCC solenoid pins - if extremely high or over limit (OL), suspect the internal harness or TCC solenoid (removing the transmission oil pan may be necessary). Tests: Wiring harness to transmission damaged, loose connection, open or shorted circuit
  4. Test the wiring between the TCM and the transmission case connector; check for a short to ground - resistance to a known good ground should be very high or OL. Tests: Wiring harness to transmission damaged, loose connection, open or shorted circuit
  5. Check TCC solenoid resistance at the transmission case after removing the harness plug; compare to manufacturer specifications.
  6. Check for voltage on the power side circuit of the TCC solenoid with key on/engine off - battery voltage should be present.
  7. Monitor the TCM with an advanced scan tool to confirm it is commanding the TCC solenoid and compare commanded vs actual feedback; the solenoid is normally duty-cycle controlled.
  8. To verify the TCM is sending the signal, use a graphing multimeter set to duty cycle - if it stays at 0% or 100% or is intermittent, re-check connections; if wiring and solenoid are good, the TCM may be at fault.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$40 – $400
Labor$100 – $600

TCC solenoid or transmission wiring harness repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2770 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Harness checks and resistance tests are DIY; the solenoid may be inside the pan and TCM testing needs an advanced scanner.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →