Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonStarts moderate but can progress to severe rapidly - slipping and overheating cause internal damage. Fix promptly, avoid highway trips.
The F shift solenoid circuit is malfunctioning - the transmission may slip or go into limp mode.
Key facts
P2706 means shift Solenoid F Malfunction. The F shift solenoid circuit is malfunctioning - the transmission may slip or go into limp mode. WrenchFair's published fair-price range for this repair is $60–$800 parts and $150–$1500 labor at independent shops.
WrenchFair rates P2706 a 4-of-5 DIY difficulty (“Fluid and filter service and wiring inspection are DIY; solenoid or valve body replacement needs pan removal and transmission-specific knowledge.”) with a “Diagnose soon” driveability rating: Starts moderate but can progress to severe rapidly - slipping and overheating cause internal damage. Fix promptly, avoid highway trips. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
transmission slipping
transmission overheating
transmission catches in gear
decreased fuel economy
possible misfire-like symptoms
vehicle enters limp mode
check engine light illuminated
Likely causes
Insufficient fluid level
Dirty or contaminated fluid
Dirty or clogged transmission filter
Defective transmission valve body
Restricted hydraulic passages
Internal transmission failure
Faulty shift solenoid
Corroded or damaged connector
Faulty or damaged wiring
Faulty PCM
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research Technical Service Bulletins for the specific vehicle by year, model, and transmission. Tests: Dirty or clogged transmission filter
Check vehicle records to verify the last time the filter and fluid were changed.
Make sure the fluid level is correct and inspect the fluid condition for contamination. Tests: Insufficient fluid level
Perform a thorough visual inspection of associated wiring for scraping, rubbing, bare wires, or burn spots.
Check all connectors and connections (to the transmission solenoids, transmission pump, and PCM) for security, corrosion, and damaged pins.
Inspect the transmission linkage for security and binding issues.
Common repairs: changing the fluid and filter, repairing or replacing the faulty shift solenoid, repairing or replacing the valve body, flushing to clean passages, cleaning connector corrosion, repairing wiring.
Advanced diagnosis needs a digital multimeter and the vehicle-specific troubleshooting chart (voltage requirements vary by year and model). Perform continuity checks with power removed - normal wiring/connections should read 0 ohms.
Typical price range
Parts$60 – $800
Labor$150 – $1500
Fluid/filter service or shift solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2706 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Fluid and filter service and wiring inspection are DIY; solenoid or valve body replacement needs pan removal and transmission-specific knowledge.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →