Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonModerately severe - you may still drive it, but intermittent fuel delivery and an erratic fuel mixture can cause severe engine damage. Diagnose promptly; do not trust it on long trips.
The secondary fuel pump circuit voltage is too low - the engine may stall or refuse to start.
Key facts
P2633 means fuel Pump B Control Circuit Low. The secondary fuel pump circuit voltage is too low - the engine may stall or refuse to start. WrenchFair's published fair-price range for this repair is $60–$500 parts and $100–$500 labor at independent shops.
WrenchFair rates P2633 a 4-of-5 DIY difficulty (“Visual inspection and ground checks are DIY; tracing CAN bus and control-module circuits needs a multimeter and wiring diagrams.”) with a “Diagnose soon” driveability rating: Moderately severe - you may still drive it, but intermittent fuel delivery and an erratic fuel mixture can cause severe engine damage. Diagnose promptly; do not trust it on long trips. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light illuminated
engine will not start
engine misfire or stall
engine starts but dies
reduced fuel economy
engine cranks fine but does not start
engine dies when reaching operating temperature
Likely causes
Issues with the fuel pump itself
Severed or damaged ground wire in the device control module
Unattached ground strap in the control module
Open, shorted, or corroded wiring in the CAN bus
Faulty CAN bus
Unsecured harnesses and wires causing chafing or broken circuits
High resistance in circuit (melted/corroded connectors, internal wire corrosion)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research Technical Service Bulletins for the specific vehicle by year, model, and power plant.
Scan and test each module with an OBD-II scanner to assess the overall electrical condition.
Visually inspect connectors and wiring (often under the vehicle near the fuel tank, susceptible to road debris) and repair anything obviously damaged. Tests: Severed or damaged ground wire in the device control module
Examine ground circuits using an auxiliary ground cable - if the problem disappears with the auxiliary ground but returns with the OEM ground, the ground cable is faulty; inspect for corroded connections and green corrosion rings. Tests: High resistance in circuit (melted/corroded connectors, internal wire corrosion)
Using an electrical wiring diagram, identify the fuel pump B control circuit and trace individual wires for breaks or shorts to ground; repair by soldering or butt connectors with heat shrink.
Use a multimeter to measure resistance between connectors in the circuit to pinpoint the fault.
Note: the code may take several drive cycles to clear; drive for about a week - if the CEL stays off, the issue is most likely resolved.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $500
Labor$100 – $500
Fuel pump or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2633 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Visual inspection and ground checks are DIY; tracing CAN bus and control-module circuits needs a multimeter and wiring diagrams.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →