P247D: Exhaust Gas Temperature Out of Range Bank 2 Sensor 2
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSeverity ranges from just a check engine light to stalling or a no-start condition.
The second exhaust temperature sensor on bank 2 (the side without cylinder #1) is reading outside the normal range.
Model notes: Applies to Ford, VW/Volkswagen, Audi, Porsche, Chevy, Nissan - diesel, gasoline, and turbocharged engines.
Key facts
P247D means exhaust Gas Temperature Out of Range Bank 2 Sensor 2. The second exhaust temperature sensor on bank 2 (the side without cylinder #1) is reading outside the normal range. WrenchFair's published fair-price range for this repair is $50–$300 parts and $80–$200 labor at independent shops.
WrenchFair rates P247D a 3-of-5 DIY difficulty (“Locating the sensor, visual wiring inspection, carbon-buildup check, and TSB research are DIY-friendly; voltage/resistance testing per specs is intermediate.”) with a “Diagnose soon” driveability rating: Severity ranges from just a check engine light to stalling or a no-start condition. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine may stall
engine may not start
engine may overheat
poor fuel economy
poor performance
check engine light illuminated
Likely causes
Defective exhaust gas temperature sensor
Faulty or damaged wiring
Corroded or damaged connector
Excessive exhaust leak
Blown fuse or fuse-able link (if applicable)
Excessive carbon buildup on sensor
Faulty ECU (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research Technical Service Bulletins for the specific vehicle by year, model, and powertrain.
Locate the exhaust gas temperature sensor (typically a 2-wire sensor in the exhaust down pipe) and perform a thorough visual inspection of wiring for scraping, rubbing, bare wires, or burn spots. Tests: Defective exhaust gas temperature sensor
Check connectors for security, corrosion, and damaged pins. Tests: Corroded or damaged connector
Remove the sensor and inspect for excessive carbon buildup; clean as needed. Tests: Excessive carbon buildup on sensor
Identify and repair any exhaust leaks near the sensor.
Check for a blown fuse or fuse-able link in the circuit if applicable.
Test the sensor per vehicle technical data - voltage output should vary proportional to temperature; resistance should vary with temperature per the sensor type.
Repair or replace faulty wiring; replace the sensor if it fails testing.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $300
Labor$80 – $200
Exhaust gas temperature sensor replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P247D ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Locating the sensor, visual wiring inspection, carbon-buildup check, and TSB research are DIY-friendly; voltage/resistance testing per specs is intermediate.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →