Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonKnock/detonation can range from a bad sensor to catastrophic internal engine damage. Diagnose as soon as possible; if you hear actual engine knock, do not keep driving.
The knock sensor on cylinder 4 is reporting engine knock above normal limits - either real knocking or a faulty sensor.
Model notes: Applies to Mercedes-Benz, Ford, Sprinter, Nissan. The knock sensor typically threads into the engine block - use caution with hot coolant or oil when removing it.
Key facts
P2339 means cylinder 4 Above Knock Threshold. The knock sensor on cylinder 4 is reporting engine knock above normal limits - either real knocking or a faulty sensor. WrenchFair's published fair-price range for this repair is $30–$100 parts and $100–$300 labor at independent shops.
WrenchFair rates P2339 a 4-of-5 DIY difficulty (“Knock sensor replacement often requires reaching under the intake manifold; continuity testing with a DVOM is intermediate.”) with a “Diagnose soon” driveability rating: Knock/detonation can range from a bad sensor to catastrophic internal engine damage. Diagnose as soon as possible; if you hear actual engine knock, do not keep driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
engine noise
diminished engine performance
reduced fuel efficiency
other related codes
there may be no distinguishable symptoms
Likely causes
Bad knock sensor
Mistimed engine or improper fuel type
Open or shorted wiring or wiring connectors
Engine noise caused by component failure
PCM or programming error
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Make sure the engine is filled to the proper level with the appropriate oil and that the oil is in good working order; eliminate actual engine noise (spark knock) before diagnosing the code. Tests: Engine noise caused by component failure
Research technical service bulletins for the specific vehicle first.
Retrieve stored codes and freeze frame data, record them, clear codes, and test-drive.
Visually inspect related wiring and connectors; repair or replace wiring that has been cut, burned, or damaged. Tests: Open or shorted wiring or wiring connectors
Disconnect the PCM and use the DVOM to check continuity in the knock sensor circuit from the sensor back to the PCM connector.
The code is usually attributable to a PCM programming error, a defective knock sensor, or actual spark knock.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $100
Labor$100 – $300
Knock sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2339 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Knock sensor replacement often requires reaching under the intake manifold; continuity testing with a DVOM is intermediate.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →