P2264

P2264: Water in Fuel Sensor Circuit

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The sensor that detects water or contamination in the fuel is sending a bad signal - your fuel may be contaminated.

Model notes: Common on Land Rover (Range Rover), Ford, Hyundai, Jeep, Mahindra, Vauxhall, Dodge, Ram, Mercedes. Seen on 2006 Vauxhall Astra 1.3 diesel (with P0400, P0090, P0108, P0190).

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 7 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Research technical service bulletins for the specific vehicle first.
  2. Check vehicle records for when the fuel filter was last replaced; visually inspect the filter. Tests: Defective or worn fuel filter
  3. Take a fuel sample in a glass jar and let it settle - water and fuel will separate in minutes; water present means contaminated fuel and/or a defective fuel filter. Tests: Defective water in fuel sensor
  4. Locate all water in fuel circuit components (sensor is normally mounted on top of the fuel tank) and perform a thorough visual inspection of wiring and connectors for scraping, rubbing, bare wires, burn spots, corrosion, or damaged pins. Tests: Defective water in fuel sensor
  5. For advanced diagnosis, use a digital multimeter or oscilloscope: signal pulses 50 to 150 hertz, with 50 hertz representing clean fuel and 150 hertz representing high contamination.
  6. Verify the sensor supply voltage (typically approximately 5-volts from the PCM) and ground; continuity testing should be done with power removed.
  7. Common mistake: replacing the PCM or sensor when damaged wiring or contaminated fuel is the actual cause.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$20 – $150
Labor$50 – $200

Fuel filter replacement and fuel system cleanup. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2264 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Fuel sampling and fuel filter replacement are intermediate work; advanced signal testing requires an oscilloscope.

Watch this repair on YouTube

Parts & tools

Fuel system toolkit — what the job actually takes

Torque specs: Fuel rail bolts: typically 8–12 Nm — verify spec.

Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →