P222E: Barometric Pressure Sensor B Intermittent/erratic
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonModerately high: a fault affecting air-fuel ratios directly should not be driven on; left unattended it can cause expensive internal engine damage.
Your second atmospheric pressure sensor (sensor B) is cutting in and out, so the air-fuel mixture keeps changing unexpectedly.
Model notes: Applies to Chevy, Mazda, Volvo, Acura, Honda, BMW, Isuzu, Mercedes-Benz, Cadillac, Hyundai, Saab, Ford, GMC.
Key facts
P222E means barometric Pressure Sensor B Intermittent/erratic. Your second atmospheric pressure sensor (sensor B) is cutting in and out, so the air-fuel mixture keeps changing unexpectedly. WrenchFair's published fair-price range for this repair is $50–$180 parts and $75–$250 labor at independent shops.
WrenchFair rates P222E a 2-of-5 DIY difficulty (“Sensor location varies; replacement is straightforward once found, but verify with manufacturer-specified electrical values.”) with a “Diagnose soon” driveability rating: Moderately high: a fault affecting air-fuel ratios directly should not be driven on; left unattended it can cause expensive internal engine damage. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
lack of engine power and performance (or limited)
engine misfiring
abnormal engine noises
fuel smell
decreased fuel economy
decreased throttle responsiveness
Likely causes
Defective or damaged BAP (barometric air pressure) sensor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Locate the BAP sensor on your vehicle; locations vary significantly, so identifying the correct sensor is the highest priority. Inspect it for physical damage, considering its surroundings (heat, vibration, road debris). Tests: Heat damage
Verify the sensor connector is fully seated; engine-mounted sensors can loosen from vibration. Tests: Defective or damaged electrical connector
Disconnect the battery before disconnecting any sensor to avoid damaging electrical spikes. Tests: Defective or damaged electrical connector
Check that nothing is obstructing the sensor, which can cause false atmospheric pressure readings. Tests: Defective or damaged BAP (barometric air pressure) sensor
With the connector disconnected, use a multimeter to compare the sensor electrical values against manufacturer-specified values. Values out of range indicate a defective sensor; replace it following proper removal/replacement procedures.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $180
Labor$75 – $250
Barometric pressure sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P222E ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor location varies; replacement is straightforward once found, but verify with manufacturer-specified electrical values.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →