Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonModerately high severity - directly affects air/fuel ratios. Diagnose promptly; if left unattended it could cause expensive internal engine damage.
The barometric pressure (atmospheric pressure) sensor A is malfunctioning - the ECM cannot properly adjust the fuel mixture.
Model notes: Common on Toyota vehicles (RAV4 turbo-diesel, Avensis Verso D4D). Also seen on Chevy, Mazda, Volvo, Acura, Honda, BMW, Isuzu, Mercedes Benz, Cadillac, Hyundai, Saab, Ford, GMC.
Key facts
P2226 means barometric pressure sensor a. The barometric pressure (atmospheric pressure) sensor A is malfunctioning - the ECM cannot properly adjust the fuel mixture. WrenchFair's published fair-price range for this repair is $30–$150 parts and $50–$150 labor at independent shops.
WrenchFair rates P2226 a 2-of-5 DIY difficulty (“Locating and inspecting the sensor and connector is beginner-to-intermediate work.”) with a “Diagnose soon” driveability rating: Moderately high severity - directly affects air/fuel ratios. Diagnose promptly; if left unattended it could cause expensive internal engine damage. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Locate the BAP sensor on your vehicle - locations vary significantly.
Inspect the BAP sensor for physical damage; consider its surroundings (heat, vibration, road debris). Tests: Heat damage
Make sure the connector is seated properly; check for loose or damaged connections. Tests: Defective or damaged electrical connector
Disconnect the battery before disconnecting any sensors.
Check for anything obstructing the sensor that could cause false readings.
Test the sensor with a multimeter per manufacturer-specific diagnostic procedures.
Replace the sensor if out of the specific range.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $150
Labor$50 – $150
Barometric pressure sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2226 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Locating and inspecting the sensor and connector is beginner-to-intermediate work.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →