P2141: EGR throttle position control circuit A low
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonEGR throttle valve malfunction can affect aftertreatment regeneration and emissions performance.
The signal to the EGR throttle valve is too low - the computer is seeing less voltage than it expects on that control circuit.
Key facts
P2141 means eGR throttle position control circuit A low. The signal to the EGR throttle valve is too low - the computer is seeing less voltage than it expects on that control circuit. WrenchFair's published fair-price range for this repair is $100–$500 parts and $100–$300 labor at independent shops.
WrenchFair rates P2141 a 3-of-5 DIY difficulty (“Locating the valve and visually inspecting wiring and connectors is DIY-friendly; circuit testing needs a multimeter.”) with a “Diagnose soon” driveability rating: EGR throttle valve malfunction can affect aftertreatment regeneration and emissions performance. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
longer than normal active aftertreatment regeneration times
Likely causes
Short to voltage, ground, or other fault in the signal circuit to the EGR throttle control valve
EGR throttle control valve faulty - internally shorted
Corroded or damaged connector or wiring
Failed PCM (unlikely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your vehicle.
Locate the EGR throttle control valve - between the intake manifold and the air filter, similar to a throttle body. Tests: Short to voltage, ground, or other fault in the signal circuit to the EGR throttle…
Visually inspect the connectors and wiring for scraping, rubbing, bare wires, burn spots, or melted plastic. Tests: Corroded or damaged connector or wiring
Pull the connectors apart and inspect the terminals for burning or corrosion - clean and apply dielectric grease. Tests: Corroded or damaged connector or wiring
Clear the codes and see if P2141 returns.
With the harness disconnected, test the EGR throttle control valve signal circuit with a DVOM - check for the 5-volt reference.
Verify a good ground at the valve; wiggle the harness while testing for an intermittent connection.
If all tests pass and the code returns, the EGR throttle control valve is likely failed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $500
Labor$100 – $300
EGR throttle control valve replacement, wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2141 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Locating the valve and visually inspecting wiring and connectors is DIY-friendly; circuit testing needs a multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →