P212A: Throttle Position Sensor/switch G Circuit Malfunction
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe PCM cannot trust the throttle position signal - misfiring, poor idle, and stalling are likely. Diagnose immediately.
The computer is not getting a valid signal from the throttle position sensor circuit G.
Key facts
P212A means throttle Position Sensor/switch G Circuit Malfunction. The computer is not getting a valid signal from the throttle position sensor circuit G. WrenchFair's published fair-price range for this repair is $20–$120 parts and $50–$200 labor at independent shops.
WrenchFair rates P212A a 3-of-5 DIY difficulty (“Scan tool voltage sweep checks are easy; wiring and PCM checks are intermediate; some TPS sensors require fine adjustment.”) with a “Diagnose soon” driveability rating: The PCM cannot trust the throttle position signal - misfiring, poor idle, and stalling are likely. Diagnose immediately. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
malfunction indicator lamp illumination
misfiring at idle or at highway speed
poor idle quality
possibly will not idle
possibly starts and stalls
Likely causes
Bad throttle position sensor (TPS)
Sticking throttle return spring
MAP or TPS connector corrosion
Misrouted harness causing chafing
Bad PCM
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
With KOEO (key on, engine off), observe TPS voltage on the scan tool; with the throttle closed it should be about 0.45 volts and gradually sweep up to approximately 4.5 to 5 volts as you depress the throttle. Tests: Bad throttle position sensor (TPS)
If you notice a glitch in the TPS sweep voltage (sometimes only a scope can capture an intermittent glitch), replace the TPS.
If the voltage is not about 0.45 volts (plus or minus 0.3) with the throttle closed or the reading is stuck, unplug the TPS connector and check for the 5-volt reference and a good ground at the connector. Tests: Bad throttle position sensor (TPS)
Check the signal circuit for continuity by jumping a fused wire between the ground circuit and the signal circuit of the TPS connector; if the scan tool reading now reads zero, replace the TPS. Tests: MAP or TPS connector corrosion
If the reading does not change to zero, check for an open or short on the signal wire; if none is found, suspect a bad PCM.
If manipulating the TPS wiring harness causes any change in idle, suspect a bad TPS.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$20 – $120
Labor$50 – $200
Throttle position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P212A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Scan tool voltage sweep checks are easy; wiring and PCM checks are intermediate; some TPS sensors require fine adjustment.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →